manualshive.com logo in svg

Schmalz Jumbo Ergo, Operating Instructions Manual, Page: 25 / 57

Share
Download
Schmalz Jumbo Ergo Operating Instructions Manual Download Page 25

 

 

DELIVERY, PACKAGING AND TRANSPORT 

30.30.01.00173/04 

www.schmalz.com 

EN   | 25 

4  Delivery, Packaging and Transport 

4.1  Delivery 

4.1.1 Included in delivery 

Refer to the order confirmation for specific details about the scope of delivery. The weights and 
dimensions will be listed in the delivery notes. 

 

 

4.1.2 Check for completeness 

Check the entire delivery against the delivery notes supplied to make sure nothing is missing. 
 

4.1.3 Report damage 

Following delivery of the shipment, damage caused by defective packaging or in transit must be 
reported immediately to the carrier and J. Schmalz GmbH.  

4.2  Packaging 

 

The operating instructions are an integral part of the vacuum tube lifter JUMBO and 
must accompany the device whenever it moves to a new location.

The packaging material must be disposed of in accordance with country-specific 
laws and guidelines. Labeled transport aids and safety mechanisms must be 
removed.

The vacuum tube lifter 

J

UMBO 

is transported in a cardboard box or 

wooden crate. 
 

 

Summary of Contents for Jumbo Ergo


























































Reviews:

No comments