Schiller Grounds Care 942630 Parts & Operators Manual Download Page 12

Page: 12 / 72

XRZ PRO RS

SET UP INSTRUCTIONS

TOOLS REQUIRED FOR ASSEMBLY

- Wrecking bar

- Claw hammer

- Sockets: 1/2”, 15/16

- Wrenches: 18mm, 1/2”, 9/16”, 3/4”, 15/16”

- Tire pressure gauge

NOTE:

All references below to the “right” or “left” are with respect to an operator at the controls.

UNCRATE UNIT

a) Discard packing materials. Loosen the caster wheel axle bolts and bumper bolts to remove the shipping

brackets.

Discard shipping brackets.

b) Re-install and tighten bumper bolts.
c) Tighten caster wheel axle bolts against caster axle spanner bushings to 80 ft/lbs.

TIRE PRESSURE

a) Set rear tire pressures to 12 lbs/in

(0.8 kg/cm

). Front tires should be kept inflated to 15 lbs/in² (1.05 kg/

cm²). Tires are overinflated for shipping.

TRACTION LEVERS

a) Tighten bolt

Summary of Contents for 942630









































































Search results

Summary of Contents for 942630

Reviews:

Related manuals for 942630

Brands by name

Popular brands

Schiller Grounds Care 942630, Parts & Operators Manual

Search results

Summary of Contents for 942630

Reviews:

Related manuals for 942630

Brands by name

Popular brands