Schiller Grounds Care 942630 Parts & Operators Manual Download Page 37

Page: 37 / 72

XRZ PRO RS

BELT REPLACEMENT

NOTE:

Always use Schiller Grounds Care, Inc. replacement belts, not general purpose

belts. Schiller Grounds Care, Inc. belts are specially designed for use on this mower and

will normally last longer.

CUTTERDECK BELT

1. Remove floorplate.

2. Set the cutterdeck in a middle height-of-cut posi-

tion.

3. Use a 3/8" ratchet and extension to back

tensioning idler off to remove belt from idler.

Remove belt from cutterdeck pulleys.

NOTE:

Use the 3/8" ratchet in the square hole

the idler.

4. Remove belt from clutch pulley.
5. Install the new belt by performing these steps in

reverse order.

BELT TENSION

NOTE:

61" cutterdeck may require tension spring

adjustment after belt installation. See Belt tension

below.

3 SPINDLE DECK

BELT TENSION FOR 61" DECK

All belts are tensioned by spring loaded idlers and do

not require any adjustment except for the 61"

cutterdeck. Use the eyebolt to adjust the spring

length to be between 6 3/4" - 7 1/2" as pictured.

Summary of Contents for 942630









































































Search results

Summary of Contents for 942630

Reviews:

Related manuals for 942630

Brands by name

Popular brands

Schiller Grounds Care 942630, Parts & Operators Manual

Search results

Summary of Contents for 942630

Reviews:

Related manuals for 942630

Brands by name

Popular brands