Schiller Grounds Care 942630 Parts & Operators Manual Download Page 38

Page: 38 / 72

XRZ PRO RS

BELT REPLACEMENT

SEAT

1. The seat is adjustable. From the operator's posi-

tion, push the seat lever

toward the left and

slide the seat forward or backward to the desired

location.

2. Have the seat in the rear most position prior to

tilting.

HYDRO TRANSAXLE DRIVE BELT

1. Remove cutterdeck belt (see cutterdeck belt

replacement).

2. Disconnect wire

at clutch

. Remove bolts

and remove torque restraint.

3. Using a ratchet with a 9/16" socket, place over

nut at location

. Use the ratchet to rotate it

enough to remove the transaxle drive belt.

4. Install a new transaxle drive belt by performing

these steps in reverse order.

5. Inspect the fans. Replace if worn or damaged.

Torque transaxle pulley nut to 28.3-41.6 ft-lbs

(38-56 Nm).

6. Reinstall cutterdeck belt (see cutterdeck belt

replacement).

Summary of Contents for 942630









































































Search results

Summary of Contents for 942630

Reviews:

Related manuals for 942630

Brands by name

Popular brands

Schiller Grounds Care 942630, Parts & Operators Manual

Search results

Summary of Contents for 942630

Reviews:

Related manuals for 942630

Brands by name

Popular brands