Schiller Grounds Care 942630 Parts & Operators Manual Download Page 35

Page: 35 / 72

XRZ PRO RS

ADJUSTMENTS

PARKING BRAKE

NOTE:

There are 2 brakes, 1 on each transaxle.

The parking brake should keep the machine from

moving. To check the parking brake, park the ma-

chine on a level surface, open the bypass valves and

set the parking brake to

. Attempt to move the

machine forward and backward by pushing it. If the

machine moves, adjust the parking brake linkage as

follows:

1. Move the machine to a flat horizontal surface.

2. Move the parking brake handle to the OFF posi-

tion.

3. Remove cotter pin

from each brake link

and

brake rod

. Slide brake rod

out of each brake

link

and insure that the brake links are rotated

toward the rear of the machine. Reinsert rod

into each link

and secure with cotter pin

4. The parking brake handle should be approxi-

mately horizontal when in the Off position. If the

brakes need to be adjusted, loosen the inner nut

of the brake rod

. Tighten the outer nut

needed for the brakes to be engaged. Tighten in-

ner nut

5. Tighten brake nut

as needed. The length of

the threads protruding past the nut should mea-

sure 1/4" - 3/8".

6. Retest to insure the machine does not move.

Summary of Contents for 942630









































































Search results

Summary of Contents for 942630

Reviews:

Related manuals for 942630

Brands by name

Popular brands

Schiller Grounds Care 942630, Parts & Operators Manual

Search results

Summary of Contents for 942630

Reviews:

Related manuals for 942630

Brands by name

Popular brands