![background image](http://html.mh-extra.com/html/scag-power-equipment/cheetah-ii/cheetah-ii_operators-manual_1205794022.webp)
16
R
Section 4
4.2 CONTROLS IDENTIFICATION
1. Ignition Switch (Figure 4-2).
The ignition switch
is used to start the engine and has three positions;
OFF, ON, and START.
2. Mower Deck Switch (Figure 4-2).
Used to engage
and disengage the mower drive system. Pulling up
on the switch will engage the deck drive. Pushing
down on the switch will disengage the deck drive.
3. Engine Choke Control (Figure 4-2).
Used to start a
cold engine.
4. Engine Throttle Control (Figure 4-2).
Used to
control the engine speed. Pushing the lever forward
increases engine speed. Pulling the lever back
decreases engine speed. Full back position is the
IDLE position. Full forward is the cutting position.
5. Left Steering Control (Figure 4-2).
Used to control
the mower's left wheel when traveling forward or
reverse.
6. Right Steering Control (Figure 4-2).
Used to
control the mower's right wheel when traveling
forward or reverse.
7. Fuse Holders (Figure 4-2).
Two 20-amp fuses
protect the mower’s electrical system. To replace
fuses, pull fuse out of the socket and install a new
fuse.
8. Parking Brake Control (Figure 4-2).
Used to
engage and disengage the parking brakes. Push the
brake pedal forward and pull the brake latch lever
back to engage the parking brakes. Push the brake
pedal fully forward, then release, to disengage the
parking brakes.
9. Fuel Tank Gauge (Figure 4-2).
Indicates the amount
of fuel in the fuel tank.
10. Dump Valve Control Levers (Figure 4-3).
Located
on the hydraulic axles, used to “free-wheel” the
mower. Rotating the levers clockwise until they
stop allows the unit to move under hydraulic power.
Rotating the levers counter-clockwise allows the
mower to be moved by hand (free-wheeling).
DUMP VALVE
CONTROL
Figure 4-3. Dump Valve Control
11. Deck Lift Foot Lever (Figure 4-2).
Used to raise
and lower the cutter deck. Push full forward to lock in
the transport position.
12. Cutting Height Adjustment (Figure 4-2).
Used to
set the cutter deck at the desired cutting height.
13. Deck Release Lever (Figure 4-1).
Used to lock the
cutter deck in the transport position. Push the foot
pedal forward and pull back on the release lever to
release the cutter deck for normal mowing.
14. Speed Control Lever (Figure 4-2).
Used to
select the mowers operating range. For the best
performance while cutting, the LOW speed should
be selected. HIGH speed should be selected for
transport operation.
15. Suspension Control Lever (Figure 4-2).
Used to
select the optimum suspension rate based on the
operator.
16. Seat Belt (Figure 4-2).
Used to secure the operator.
Seat belt must be worn at all times when the ROPS
is in the upright and locked position.
17. Seat Hold Down Release Latch (Figure 4-2).
Located behind the seat. Used to secure the seat
in the operator's position. Release the latch to gain
access under the seat.
18. Check Engine Light (Figure 4-2).
Indicates the
operation of the engine sensors on the Fuel Injection
Engines (EFI). If a problem occurs with a sensor
on the engine, the light will flash a code. See your
authorized Scag Dealer for diagnosis and repair.
Summary of Contents for CHEETAH II
