SBC PCD7.L630 Instruction Manual Download Page 32

Page: 32 / 46

Saia-Burgess Controls AG

Manual for PCD7.L6xx room operator units

│

Document 26

-859

NG07 │ 2015-06-04

Digital room controller units

3-21

Function

Description

Temperature measurement

The integrated temperature sensor can be used to meas

ure the room temperature.

To activate parameterisation, the

and

keys should be pressed together. The temperature

symbol on the display will then flash and the current set

ting will be displayed.
OFF: Temperature measurement disabledIf the room con

troller uses the temperature measurement from the room

control unit, the current room temperature in the room

controller will become invalid (99.9°C). See room control

ler configuration.
ON: Temperature measurement is enabled. The room

temperature will be transmitted after any 0.2°C change or

after 15 minutes without any change.
ON with temperature display: Temperature measurement

is enabled and the current room temperature will be per

manently shown on the display.

Factory setting: OFF

Retain settings

The settings for the fan and the set-point displacement

may be permanently applicable or only valid for the current

configuration step.
Retain settings

Press

and

keys together for at least 5 seconds. The

temperature and fan symbols will flash and status ON will

be displayed.Settings are only valid for the current con

figuration step.

Press

and

keys together for at least 5 seconds. The

temperature and fan symbols will flash and status OFF will

be displayed.

Factory setting: ON

Blind rotation

The rotation function can be used to control venetian

blinds. When active, the rotation command is issued with

the

key.

Deactivate rotation functionPress the

and

keys

together. On the display, the rotation symbol will flash and

the status text OFF will be displayed.
Activate rotation function

Press the

and

keys together. On the display, the

rotation symbol will flash and the status text ON will be

displayed.

Factory setting: OFF

Summary of Contents for PCD7.L630















































Search results

Summary of Contents for PCD7.L630

Reviews:

Related manuals for PCD7.L630

Brands by name

Popular brands

SBC PCD7.L630, Instruction Manual

Search results

Summary of Contents for PCD7.L630

Reviews:

Related manuals for PCD7.L630

Brands by name

Popular brands