manualshive.com logo in svg

Sawo STN Series, Manual, Page: 21 / 26

Share
Download
Sawo STN Series Manual Download Page 21

TECHNICAL GUIDE

STN Steam Generators

www.sawo.com | [email protected]

21

Cabin lights / 

Dimmer

230/12, 24, 230

FAN

SCENT PUMP

TEMP

SWITCH

(24VAC)DRAIN

(230VAC) LIGHT

(12VDC)ILL

FAN

SCENT PUMP

TEMP

SWITCH

(24VAC)DRAIN

(230VAC) LIGHT

(12VDC)ILL

Cabin Light

For safety reasons use step down transformer 24-12VAC and low voltage lighting fixture.
If 230VAC is used, it’s highly recommended to use isolation transformer.

Steam room light can be connected to steam generator’s light output. Output is 230VAC fused.

Demand Button

• 

IP 68 sealed when panel mounted.

• 

Can be installed inside or outside steam room. 

• 

Button has blue ring illumination. 5VDC and 20mA. Make sure polarity is right when connecting illumination wires.  

• 

4-pole connection cable. 2 poles for switch and 2 poles for illumination.

10 meters connection cable

Wire Color Connections

Terminal block (Steam Generator)

Terminal block

Demand Button

Connection 

Cable

Red
Yellow
Grey
White
Brown
Green

Switch
Switch
-ILL
-ILL
-ILL
+ILL

Terminal Block

Terminal Block

Summary of Contents for STN Series



























Reviews:

No comments