SANKI S-CON MINI SLIM Operating And Service Manual Download Page 18

Page: 18 / 20

CHECKING

PERIOD

PART TO

CHECK

THINGS TO

CHECK FOR

CHECKING

METHOD

REMEDY

Daily

Belt

Foreign substances on

surface and undersurface

Visual inspection

Clean and remove any

foreign matter.

Dislodgment from V-form

belt guidance grooves

Visual inspection

Inspection, adjustment

Getting jammed

Visual inspection

Inspection, adjustment

Drive pulley

and other

pulleys

Foreign substances

Visual inspection

Clean and remove any

foreign matter.

Three

monthly

Geared motor

Rotation malfunction,

inappropriate installation

Visual inspection

and manual check

Inspection

Tighten loose attachment

bolts.

Overheat, abnormal noise

Manual check and

listening

Inspection and adjustment

or replacement

Six

monthly

Drive pulley

Wear of surface,

rotation malfunction

Visual inspection

and manual check

Inspection and adjustment

or replacement

Pulleys and

rollers

Rotation malfunction,

loose attachment bolts

Visual inspection

and manual check

Inspection, repair

Tighten loose attachment

bolts.

Overheat of bearings,

abnormal noise

Manual check and

listening

Inspection and adjustment

or replacement

Frame and

stand units

Attachments

Loose attachment bolts

Visual inspection

and manual check

Tighten loose attachment

bolts.

Damage of each part

Visual inspection

and manual check

Inspection and adjustment

or replacement

11-2. ITEMS FOR REGULAR INSPECTION

Summary of Contents for S-CON MINI SLIM





















Search results

Summary of Contents for S-CON MINI SLIM

Reviews:

Related manuals for S-CON MINI SLIM

Brands by name

Popular brands

SANKI S-CON MINI SLIM, Operating And Service Manual

Search results

Summary of Contents for S-CON MINI SLIM

Reviews:

Related manuals for S-CON MINI SLIM

Brands by name

Popular brands