background image

 

 

 
 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

     

    

 

 

 
 

 

 

 

 

 

 

 

B.

 

During Operation 

C.

 

After Use 

WARNING

Improper handling of the conveyor could result in serious physical injury or damage! 

Do NOT touch the conveyor when it is running 

  There is considerable risk of being caught and injured by the conveyor. 

Do NOT ride on or climb on the conveyor

Do NOT go under the conveyor 

  There is considerable risk of falling or being caught and injured by the conveyor. 

Beware of entanglement 

  When working close to the conveyor, take care not to get caught in the conveyor. There is 

considerable risk of being injured by the conveyor. 

Do NOT remove safety covers 

  There is a risk of getting caught in the rotating parts such as pulleys. Only remove in case of 

maintenance or inspection. 

CAUTION

Improper handling of the conveyor may result in physical injury or damage! 

Do NOT apply force to ends of conveyor 

  Do NOT press down on, or hang off the sides of the conveyor. Injury may result from a toppling 

conveyor. 

 

Secure the conveyor to the floor/ground 

  When using the conveyor, be sure to secure it to the floor/ground with anchor bolts etc. to 

prevent it from toppling irrespective of indoor use or outdoor use. 

Switch off the power after use 

  Ensure that the power is switched off when carrying out relocation, inspection, cleaning, etc. of 

the conveyor, otherwise there is a risk that the conveyor could start unexpectedly. When leaving 
the conveyor unused for a long period, take plug out of the outlet /connector to prevent electric 
shock or leakage. 

NOTE

1. Always use in accordance with the Occupational Safety and Health Act. 

                2. If the owner modifies the conveyor, any ill effects will fall outside the conditions of the guarantee. 

Do NOT start the conveyor while it is loaded 

  The motor may become damaged due to overload. Additionally, the motors of variable-speed type 

machines may burn out as a result of running at excessively low speeds for   

long periods. Use the conveyor within the specifications, indicated in the instructions for use, and 
in the catalogue.     

CAUTION

Improper handling of the conveyor may result in physical injury or damage! 

Summary of Contents for S-CON MINI SLIM





















Reviews: