Samsung WIP-500M User Manual Download Page 3

Page: 3 / 49

Step 3: Programming Wireless Voice

Enter the technician mode (MMC 800, pw: 4321).

MMC 830

Verify the desirable system IP and gateway address are in place.

e.g.

System IP: 165.213.97.185 Gateway: 165.213.97.1

MMC 831

If there is MGI card in the system, then make sure the VoIP phone and MGI IP addresses are
not conflict with VoWLAN IP addresses.

MMC 849; skip any field that is not mentioned.

Use password “0000” to enter.

[ENTER PASSWORD ]

[0000 ]

Enable VoWLAN registration.

[REGISTER VoWLAN]

[ENABLE ]

Select “Combo AP” type.

[SELECT AP TYPE ]

[COMBO WBS ]

MMC 845

Set WLAN data; use right soft key to move to the right field.

Set system ID.

[WLAN: SYSTEM ID ]

[123456 ]

ii.

Set system KEY.

[WLAN: SYSTEM KEY]

[12345 ]

iii.

Set system RF channel selection.

[WLAN: RF CHANNEL]

[USE CH 1: 01 ]

•

Use/Select channel 1, 6 and 11 only.

iv.

Set TX power level for the entire system.

[WLAN: WBS TX PWR]

[LEVEL 4 ]

Home Page

Table of Contents

Summary of Contents for WIP-500M


















































Search results

Summary of Contents for WIP-500M

Reviews:

Related manuals for WIP-500M

Brands by name

Popular brands

Samsung WIP-500M, User Manual

Search results

Summary of Contents for WIP-500M

Reviews:

Related manuals for WIP-500M

Brands by name

Popular brands