Samsung RF4402d Series Installation Manual Download Page 101

Page: 101 / 133

Confidential

Chapter

Connecting

Cables

RF4402d Series Installation Manual v1.0

Interface Cable Connection

Remove/Insert Optical Module

If the optical module needs to be removed or inserted before connecting the cable,
follow the below process.

To remove Optical Module

Hang the Optic Transceiver Removal Tool’s hook on the optical module

’

bail within the system.

Figure 74.

Optical Module Removal (1)

Completely remove the optical module from the optical module cage by
pulling the Optical Module Removal Tool.

Figure 75.

Optical Module Removal (2)

Optical Module
Removal Tool

Optical Module

Optical Module Cage

Optical
Connector

Optical Module

[System Inside]

Optical Module

Removal Tool’s Hook

Bail

[Front View]

Location to hang

the Optical Module

Removal Tool

Summary of Contents for RF4402d Series



































































































































Search results

Summary of Contents for RF4402d Series

Reviews:

Related manuals for RF4402d Series

Brands by name

Popular brands

Samsung RF4402d Series, Installation Manual

Search results

Summary of Contents for RF4402d Series

Reviews:

Related manuals for RF4402d Series

Brands by name

Popular brands