Samsung RF4402d Series Installation Manual Download Page 10

Page: 10 / 133

Confidential

Preface

RF4402d Series Installation Manual v1.0

New and Changed Information

This section describes information that has been added/changed since the previous
publication of this manual.



Added ‘Make sure RF Power Feeding Off when connecting TMA’. (Chapter 1.
While Installation)

Revision History

The following table lists all versions of this document.

Document Version

Publication Date

Remarks

1.0 November

2018 -

Organization of This Document

Section

Title

Description

Chapter 1

Before Installation

This chapter introduces RRH and describes items
should be understood before installation.

Chapter 2

Installing System

This chapter describes the procedures to install
the RRH.

Chapter 3

Connecting Cables

This chapter describes the procedures to connect
the cables to the RRH installed.

Chapter 4

Inspect the Installation

This chapter describes the procedures of
inspecting installation status after RRH
installation and cabling is completed.

Appendix A

Acronyms

This annex describes the acronyms used in this
manual.

Appendix B

Sector Antenna Installation

This annex describes the sector antenna
installation.

Appendix C

Clean the Optical Connectors

This annex describes the procedure of cleaning
the optical connector and cleaning tool.

Appendix D

Standard Torque

This annex describes the standard torque when
fastening the bolt.

Summary of Contents for RF4402d Series



































































































































Search results

Summary of Contents for RF4402d Series

Reviews:

Related manuals for RF4402d Series

Brands by name

Popular brands

Samsung RF4402d Series, Installation Manual

Search results

Summary of Contents for RF4402d Series

Reviews:

Related manuals for RF4402d Series

Brands by name

Popular brands