Samsung RF4402d Series Installation Manual Download Page 129

Page: 129 / 133

Confidential

Appendix B Sector Antenna Installation

RF4402d Series Installation Manual v1.0

114

Sector Antenna Installation

The method of sector antenna installation is as follows.

Put up an antenna pole and insert the sector antenna into the antenna pole
using a fixing clamp.

Set the antenna’s up/down tilt to 0° and fix the fixing clamps at the top and
bottom.

Adjust the tilted angle of the antenna by taking the signal strength into account.

The bolts on the upper and lower guide clamps must be loose as to allow angle
adjustment of the antenna.

After adjusting the antenna angle, tighten up the 4 loose bolts on the upper and
lower guide clamps.

Figure 104.

Sector Antenna

Antenna Input Port

Pole

Main Radiation Direction

Upper Fixing Clamp

Lower Fixing Clamp

Upper Guide Clamp

Lower Guide Clamp

Guide Clamp Bolt_2

Guide Clamp Bolt_1

Guide Clamp Bolt_3

Guide Clamp Bolt_4

Summary of Contents for RF4402d Series



































































































































Search results

Summary of Contents for RF4402d Series

Reviews:

Related manuals for RF4402d Series

Brands by name

Popular brands

Samsung RF4402d Series, Installation Manual

Search results

Summary of Contents for RF4402d Series

Reviews:

Related manuals for RF4402d Series

Brands by name

Popular brands