manualshive.com logo in svg

Samsung RC090MHXEA, Service Manual, Page: 22 / 52

Share
Download
Samsung RC090MHXEA Service Manual Download Page 22

 

www.freedomhp.co.uk

 ©G Hendra Nov 18 

 

22

E231, Temperature Sensors 

E231

 is an error with the outdoor refrigerant coil sensor. It’s 

connected to the main PCB in connector at the top right of the 
PCB called CN43 in a white and red plug; it’s the 3

rd

 and 4

th

 

wire from the bottom.  

 

 

 

 

 

 

 

 

 

 

 

 

To read what this sensor is 
measuring you can ask the unit 
using the interrogation function on 
the outdoor unit main PCB  

At the bottom of the main PCB are 
4 buttons, you need to press K4, 7 
times. 

The display will show 07 XX 

The XX will be the temperature this sensor is measuring; this sensor measures the refrigerant 
temperature at the bottom of the big blue coil on the back of the outdoor unit, it’s clipped to 
the coil, you need to remove the back cover to get to it. You will need to compare the coil 
temperature with the reading, if they are different the sensor needs replacing.

  

 

NOTE: 

If your unit is constantly freezing up and not defrosting measure this 
sensor, if the coil is frozen it should read 7-XX showing a negative 
temperature. If it shows a positive temperature the sensor is faulty. 

Summary of Contents for RC090MHXEA





















































Reviews:

No comments