Samsung ProXpress M4030 Series Service Manual Download Page 121

Page: 121 / 178

4. Troubleshooting

► Error Code

A2–1210

A2–2110

► Error message

Error: #A2-1210 / Fan Failure: #A2-1210. Turn off then on. Call for service if the problem persists

Error: #A2-2110 / Fan Failure: #A2-2110. Turn off then on. Call for service if the problem persists

► Symptom

Main fan or SMPS fan is not operational.

► Troubleshooting method

NOTE

•

SMPS fan error : A2–1210

•

Main fan error : A2–2110

1) Turn the machine off then on.

2) Check if the corresponding fan connector is connected correctly.

3) If the connection is OK, Enter SVC mode and execute fan test.

(

Diagnostics > Engine Diagnostics > Engine Test Routines

)

4) If the fan is not operational, measure the fan power.

a) If 24V power is generated, replace the defective fan.

•

SMPS fan :

JC31-00152B

•

Main fan :

JC31-00161A

b) If 24V power is not generated,

•

Measure the 24V power on the SMPS board. If the SMPS board is defective, replace it.

•

If the SMPS board is normal, replace the main board.

5) If the fan operation is normal but the error persists,

a) Replace the fan.

b) If the error persists after replacing the fan, replace the main board.

4-39

Summary of Contents for ProXpress M4030 Series














































































































































































Search results

Summary of Contents for ProXpress M4030 Series

Reviews:

Related manuals for ProXpress M4030 Series

Brands by name

Popular brands

Samsung ProXpress M4030 Series, Service Manual

Search results

Summary of Contents for ProXpress M4030 Series

Reviews:

Related manuals for ProXpress M4030 Series

Brands by name

Popular brands