Samsung ProXpress M4030 Series Service Manual Download

Page: 127 / 178

4. Troubleshooting

► Error Code

H1-1222

► Error message

Tray 2 cassette Out / Tray 2 cassette is pulled out. Insert it properly

► Symptom

Tray 2 cassette is pulled out.

► Troubleshooting method

1) Insert the tray 2 cassette correctly.

2) If the problem persists, check the cassette detection sensor. If it is defective, replace it.

3) If the sensor is normal, replace the SCF board.

► Error Code

H1-1230

► Error message

Error: #H1-1230 / Tray Failure: #H1-1230. Check tray 2 connection & turn off then on. Call for service if the problem
persists

► Symptom

Connection between the main machine and the SCF unit is abnormal.

► Troubleshooting method

1) Check the harness connection between the main machine and the SCF unit.

Reconnect the harness.

2) If the problem persists, replace the SCF board.

3) If the SCF board is normal, replace the Main board.

4-45

Summary of Contents for ProXpress M4030 Series














































































































































































Search results

Summary of Contents for ProXpress M4030 Series

Reviews:

Related manuals for ProXpress M4030 Series

Brands by name

Popular brands

Samsung ProXpress M4030 Series, Service Manual

Search results

Summary of Contents for ProXpress M4030 Series

Reviews:

Related manuals for ProXpress M4030 Series

Brands by name

Popular brands