Samsung ProXpress M4030 Series Service Manual Download Page 124

Page: 124 / 178

4. Troubleshooting

► Error Code

C2–1323 / C2–1411

► Error message

Error: #C2-1323 / Toner Failure: #C2-1323: Install toner again

Toner Not Installed / Toner cartridge is not installed. Install it

► Symptom

The toner cartridge is not installed properly.

► Troubleshooting method

1) Open the front cover.

2) If the toner cartridge is not installed, install it. Try to test the machine again.

3) If the toner cartridge is installed, remove it. Check if the contact terminal is contaminated or broken.

4) Clean the contact terminal or replace the toner cartridge.

5) Check if the CRUM harness is connected correctly. Reconnect it.

6) If the harness is defective, replace it.

7) Turn the machine off then on. Try to test the machine.

► Error Code

C2–1512

► Error message

Toner Not Compatible / Toner cartridge is not compatible. Check guide

► Symptom

Toner cartridge is not compatible.

► Troubleshooting method

1) Open the front cover. Remove the toner cartridge.

2) Check if the label information of the toner cartridge is same with the machine’s one. (ex. /SEE)

3) If label information is different from the machine or the toner cartridge is not a samsung genuine, replace it with

a new one.

4-42

Summary of Contents for ProXpress M4030 Series














































































































































































Search results

Summary of Contents for ProXpress M4030 Series

Reviews:

Brands by name

Popular brands

Samsung ProXpress M4030 Series, Service Manual

Search results

Summary of Contents for ProXpress M4030 Series

Reviews:

Brands by name

Popular brands