Samsung OfficeServ 7030 Installation Manual Download Page 21

Page: 21 / 105

OfficeServ 7030 Installation Manual

TABLE OF CONTENTS

Purpose..........................................................................................................................................I

Document Content and Organization...............................................................................................I

Conventions.................................................................................................................................III

Reference.....................................................................................................................................V

Revision History............................................................................................................................V

Symbols......................................................................................................................................VII

WarningVIII

Caution X

CHAPTER 1. Before Installing

1.1 Site Information...............................................................................................................................1

1.1.1 Safety Conditions..................................................................................................................1

1.1.2 Temperature and Humidity Conditions....................................................................................1

1.2 Grounding Conditions....................................................................................................................3

1.3 Power Conditions............................................................................................................................3

1.4 Checking the Package....................................................................................................................5

1.5 Cabinet Configuration....................................................................................................................6

1.6 System Installation Procedure.....................................................................................................10

CHAPTER 2. Mounting and Replacing the Boards

2.1 Connecting the Grounding Wire....................................................................................................1

2.1.1 Opening................................................................................................................................1

2.1.2 Grounding.............................................................................................................................4

2.2 Mounting the Boards .....................................................................................................................5

2.2.1 Removing Dummy Parts.......................................................................................................5

2.2.2 Setting Switches....................................................................................................................5

2.2.3 Mounting Optional Boards ....................................................................................................7

2.2.4 Mounting the daughter Boards ..............................................................................................9

2.2.5 Closing/Cabling...................................................................................................................12

XVI

Summary of Contents for OfficeServ 7030










































































































Search results

Summary of Contents for OfficeServ 7030

Reviews:

Related manuals for OfficeServ 7030

Brands by name

Popular brands

Samsung OfficeServ 7030, Installation Manual

Search results

Summary of Contents for OfficeServ 7030

Reviews:

Related manuals for OfficeServ 7030

Brands by name

Popular brands