Samsung OfficeServ 7030 Installation Manual Download Page 6 | Manualshive

Page: 6 / 105

background image

OfficeServ 7030 Installation Manual

INTRODUCTION

Purpose

OfficeServ 7030 is the most suitable system for small offices with 10 to 20 subscribers
circuit line. This manual describes the prerequisite for the installation of the OfficeServ
7030 system as well as how to install, inspect and operate the system.

Document Content and Organization

This document consists of 7 chapters and abbreviations as follows:

CHAPTER 1. Before Installing

This chapter describes the checklists (installation site, grounding & power conditions etc.)
which should be inspected before installing the OfficeServ 7030 system. This chapter also
describes the items included in the OfficeServ 7030 package and the installation procedure.

CHAPTER 2. Mounting and Replacing the Boards

This chapter describes how to mount/replace various boards to/from the OfficeServ 7030
system.

CHAPTER 3. Installing the System

This chapter describes how to install an OfficeServ 7030 on the wall, if necessary,
depending on the installation environment.

CHAPTER 4. Connecting the Power

This chapter describes how to connect the power to the OfficeServ 7030 system.

CHAPTER 5. Connecting the C.O. Line

© SAMSUNG Electronics Co., Ltd.

I

«
...
4
5
6
7
8
...
»

Summary of Contents for OfficeServ 7030










































































































Reviews:

No comments

Related manuals for OfficeServ 7030

Brand: Samsung Pages: 34

Brand: NEC Pages: 24

Brand: Jabra Pages: 4

Brand: Grandstream Networks Pages: 6

Brand: Swisscom Pages: 25

Brand: Inter-Tel Pages: 48

Brand: AT&T Pages: 40

PHONECELL SX3e AMPS

Brand: Telular Pages: 26

Brand: ausdom Pages: 51

Brand: SOYO Pages: 9

2.0040223181058e16

Brand: Samsung Pages: 142

Brand: ETVAX Pages: 64

Brand: Siemens Pages: 269

Brand: Daewoo Pages: 30

Brand: Daewoo Pages: 102

Brand: Radio Shack Pages: 2

Brand: Radio Shack Pages: 2

Brand: Radio Shack Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands