Samsung OfficeServ 7030 Installation Manual Download Page 44

Page: 44 / 105

OfficeServ 7030 Installation Manual

2.2 Mounting the Boards

This section describes how to set the base board switches and mount the optional boards.

2.2.1 Removing Dummy Parts

Depending on daughter boards, remove the cabinet's dummy parts with a nipper.

Figure 2.6 Removing the dummy parts

2.2.2 Setting Switches

The base board and EPM board that are equipped with switches relative to the user
requirements, system configuration and/or daughter boards are as follows:

Table 2.1 Jumpers/Switches of the Base/EPM Board

Board

Switch

Description

Base

S1 (1~8)

Sets the country code and future use

EPM

S1 (1~2)

Sets whether to use the 4LM daughter board and whether
to use the Expansion cabinet.

Summary of Contents for OfficeServ 7030










































































































Search results

Summary of Contents for OfficeServ 7030

Reviews:

Related manuals for OfficeServ 7030

Brands by name

Popular brands

Samsung OfficeServ 7030, Installation Manual

Search results

Summary of Contents for OfficeServ 7030

Reviews:

Related manuals for OfficeServ 7030

Brands by name

Popular brands