Samsung OfficeServ 7030 Installation Manual Download Page 92

Page: 92 / 105

OfficeServ 7030 Installation Manual

6.2.6 Connecting the SMDR

The Station Message Detail Recording (SMDR) computer is used for recording call
information, calculating phone bills and/or displaying various analysis data based on the
call data provided by the system.

The SMDR computer can be connected via the LAN port of the 4LM board or the base
board built in the OfficeServ 7030 system.

The SMDR system specification is as follows:

Table 6.4 Specification of the SMDR System

Item

Specification

Platform

IBM PC

CPU

Pentium 586 or higher

Operating System

Windows 95/98 or later

Main Memory

32 MByte or more

To use within the company's LAN network, connect LAN to the LAN port of the Base
board, and connect a SMDR computer to the LAN.

Figure 6.14 Connecting the SMDR

OfficeServ 7030

LAN

SMDR

Summary of Contents for OfficeServ 7030










































































































Search results

Summary of Contents for OfficeServ 7030

Reviews:

Related manuals for OfficeServ 7030

Brands by name

Popular brands

Samsung OfficeServ 7030, Installation Manual

Search results

Summary of Contents for OfficeServ 7030

Reviews:

Related manuals for OfficeServ 7030

Brands by name

Popular brands