Samsung MXD-A16K1X025A Installation Manual Download

Page: 23 / 32

AHU-KIT heat exchanger EVA OUT sensor detachment error

Outdoor unit display

↔

xxx (xxx : Address of an indoor unit with an error)

Explanation

Refer to below explanation.

Reason

Indoor heat exchanger OUT sensor detachment.

1) Self check

• Check for AHU-KIT heat exchanger OUT sensor. Make sure it is in the correct location.

1) Explanation

• When testing run in Cool mode (Please, press the button for the test run inside the outdoor unit)

Tcond, out-Tair, out > 3˚C

Tair, in-Teva, in > 4˚C

Tair, in-Teva, out > 4˚C

Compressor,Indoor unit in operation.

Thermo ON

Error message

Indoor heat exchanger OUT sensor

detachment error

• Wired remote controller will show the same error shown in the outdoor unit.

Sensor Error

AHU-KIT heat exchanger IN sensor detachment error

Outdoor unit display

↔

xxx (xxx : Address of an indoor unit with an error)

Explanation

Refer to below explanation.

Reason

Indoor heat exchanger IN sensor detachment.

2) Self check

• Check for IN sensor of AHU-KIT heat exchanger. Make sure it is in the correct location.

1) Explanation

• When testing run in Cool mode (Please, press the button for the test run inside the outdoor unit)

Tcond, out-Tair, out > 3˚C

Tair, in-Teva, in > 4˚C

Tair, in-Teva, out > 4˚C

Compressor,Indoor unit in operation. Thermo ON

Error message

Indoor heat exchanger IN sensor

detachment error



TROUBLESHOOTING

(Continued)

Note

• When conditions shown in above table occurs, it is classified as

↔

xxx

• When conditions shown in above table occurs, it is classified as

↔

xxx

MXD-A16K1X025A_E_31836-1.indd 23

2010-03-12 ｿﾀﾈﾄ 12:43:07

Summary of Contents for MXD-A16K1X025A

































Search results

Summary of Contents for MXD-A16K1X025A

Reviews:

Related manuals for MXD-A16K1X025A

Brands by name

Popular brands

Samsung MXD-A16K1X025A, Installation Manual

Search results

Summary of Contents for MXD-A16K1X025A

Reviews:

Related manuals for MXD-A16K1X025A

Brands by name

Popular brands