Samsung MXD-A16K1X025A Installation Manual Download | Manualshive

Page: 22 / 32

background image

22

Initial Check-up

1) Check the connection status between Indoor unit and the AHU-KIT.

• Make sure you have followed instructions and wiring diagram shown in the installation manual.
• Make sure AHU-KIT PBA is installed in a place where there are no influence from outdoor humidity,

dust and temperature.

2) Ensure that power voltage is AC 187V~AC 253V.

3) Check each of the accessories and make sure they are in good condition.

  • CN32 : DC 11~13V (both ends)
   • IC02 G/O : DC 4.5~5.5V (both ends)
  • TRANS Output : AC 16~18V

Outdoor unit display
Explanation

Internal communication error between EEPROM and MICOM

Reason

Require to change PBA due to Bad EEPROM

EEPROM Error

• Wired remote controller will show the same error shown in the outdoor unit.

TROUBLESHOOTING

Note

MXD-A16K1X025A_E_31836-1.indd 22

2010-03-12 ｿﾀﾈﾄ 12:43:06

«
...
20
21
22
23
24
...
»

Summary of Contents for MXD-A16K1X025A

































Reviews:

No comments

Related manuals for MXD-A16K1X025A

Brand: EarthLinked Pages: 21

Brand: Magic Aire Pages: 30

Brand: SystemAir Pages: 143

Brand: ActronAir Pages: 68

Brand: Pace Pages: 108

Brand: Vents Pages: 20

Brand: Salda Pages: 40

Brand: United Technologies Pages: 60

Brand: Amana Pages: 32

Brand: York Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands