Samsung DS 5021D KEYSET General Description Manual Download

Page: 26 / 92

3.5.2 RING

The output voltage and frequency of the ring signals in the OfficeServ 7100 are as follows:

•

Output voltage: 75 Vrms Square Wave (4SLM)

•

Frequency: 20 or 25 Hz

The OfficeServ 7100 provides the users with various tones to notify the users of the status of functional opera-
tions.

The ON/OFF cycles of currently specified tones are shown in the table below.

Note: The ON/OFF cycle can be adjusted by changing the values of the system database.

*Overrides headset mode.

3.3

3.5.3 SYSTEM TONES

TONE

ON/OFF CYCLE

DIAL TONE

1000/250 ms

BUSY TONE

500/500 ms

DO NOT DISTURB TONE

250/250 ms

RING BACK TONE

1000/2000 ms

CALL PARK TONE

CONTINUOUS

CONFIRMATION/CAUTION/BARGE-IN TONE

50/50 ms

CALL BACK/HOLD TONE

500/3500 ms

RING BACK TONE

1000/2000 ms

ERROR/NUMBER UNOBTAINABLE TONE

250/250 ms

MESSAGE CAMP ON TONE

CONTINUOUS

3.6 KEYSET LED INDICATIONS

CONDITION

LED COLOR

LED ON

LED OFF

LINE IDLE

OFF

—

OFF

LINE IN USE

RED / GREEN

STEADY

—

RECALL

AMBER

500 ms

CALL ON HOLD

RED / GREEN

500 ms

RINGING C.O. CALL

GREEN

100 ms

RINGING INTERNAL CALL

GREEN

100 ms

DND INDICATION

RED

112 IPM for 500 ms

500 ms

OPERATOR CALLS

RED

100 ms

ANS / RLS (DND)*

RED

112 IPM for 500 ms

500 ms

ANS / RLS (HANDSET MODE)**

RED

STEADY

—

Home Page

Table of Contents

Summary of Contents for DS 5021D KEYSET





























































































Search results

Summary of Contents for DS 5021D KEYSET

Reviews:

Related manuals for DS 5021D KEYSET

Brands by name

Popular brands

Samsung DS 5021D KEYSET, General Description Manual

Search results

Summary of Contents for DS 5021D KEYSET

Reviews:

Related manuals for DS 5021D KEYSET

Brands by name

Popular brands