manualshive.com logo in svg

Samsung C8245, User Manual, Page: 166 / 315

Share
Download
Samsung C8245 User Manual Download Page 166

S3C8248/C8245/P8245/C8247/C8249/P8249

INSTRUCTION SET

6-59

MULT

 

—

 

Multiply (Unsigned)

MULT

dst,src

Operation:

dst  

←

  dst 

×

  src

The 8-bit destination operand (even register of the register pair) is multiplied by the source
operand (8 bits) and the product (16 bits) is stored in the register pair specified by the destination
address. Both operands are treated as unsigned integers.

Flags:

C:

Set if result is  

>

 255; cleared otherwise.

Z:

Set if the result is "0"; cleared otherwise.

S:

Set if MSB of the result is a "1"; cleared otherwise.

V:

Cleared.

D:

Unaffected.

H:

Unaffected.

Format:

Bytes

Cycles

Opcode

(Hex)

Addr Mode

dst       src

opc

src

dst

3

22

84

RR

R

22

85

RR

IR

22

86

RR

IM

Examples:

Given: Register 00H  =  20H, register 01H  =  03H, register 02H  =  09H, register 03H  =  06H:

MULT

00H, 02H

→

Register 00H  =  01H, register 01H  =  20H, register 02H  =  09H

MULT

00H, @01H

→

Register 00H  =  00H, register 01H  =  0C0H

MULT

00H, #30H

→

Register 00H  =  06H, register 01H =  00H

In the first example, the statement "MULT  00H,02H" multiplies the 8-bit destination operand (in
the register 00H of the register pair 00H, 01H) by the source register 02H operand (09H). The
16-bit product, 0120H, is stored in the register pair 00H, 01H.

Summary of Contents for C8245




























































































































































































































































































































Reviews:

No comments