Samsung AEN160YDEHA Installation Manual Download Page 32 | Manualshive

Page: 32 / 49

background image

E-

32

If the unit has some problem to work properly, the LED on hydro unit will flash and some error codes will be dis-
played on the controller.
The following table described the explanation of error codes on the LCD display.

Display

Explanation

Wired remote controller thermistor SHORT or OPEN

FRAM Read/Write Error(Wired remote controller data error)

Water Inlet thermistor SHORT or OPEN

PHE Outlet thermistor SHORT or OPEN

Water Outlet thermistor SHORT or OPEN

Water TANK thermistor SHORT or OPEN

Thermistor

X

Check its resistance. 10kohm@24°C (Hydro unit), 220kohm@24°C (DHW Tank, Solar)

X

Check its location as shown at the diagram.

X

Check its contact status with pipe.

X

Final solution is to change parts

5X

5X

5X

Water Out

Water In

Water Outlet
thermistor

E903

E902

Water inlet

E901

Wired remote controller
thermistor

E653

Water tank
thermistor

E904

PHE Outlet

Troubleshooting

«
...
30
31
32
33
34
...
»

Summary of Contents for AEN160YDEHA


















































Reviews:

No comments

Related manuals for AEN160YDEHA

Brand: Garden Oasis Pages: 12

Brand: Cantherm Pages: 11

Brand: Kärcher Pages: 18

Brand: wallas Pages: 39

Brand: Salda Pages: 16

Brand: Salda Pages: 8

Brand: Walchem Pages: 31

Brand: Zoeller Pages: 12

Brand: York Pages: 204

TURBO-FLUX modular

Brand: Cattani Pages: 61

Brand: Lasko Pages: 4

Brand: CLAS Pages: 20

Brand: Kampmann Pages: 84

Brand: York Pages: 72

Sherpa Monobloc 4

Brand: Olimpia splendid Pages: 96

Brand: IPM Pages: 24

Brand: CountyLine Pages: 20

Brand: Bionaire Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands