Samsung 2 COLOR THERMAL PRINTER SRP-370, User Manual

Page: 42 / 45

82
GS r n
[Name]
[Format]
[Range]
[Description]
Transmit status.
ASCII GS r n
Hex 1D 72 n
Decimal 29 114 n
n=1, 2, 49, 50
▪ Transmits the normal status specified by n as follows :
n Function
1, 49 Transmits paper sensor status.
2, 50 Transmits drawer kick-out connector status.
▪ Paper sensor status (n=1, 49) :
Bit Off/On Hex Decimal Function
Off 00 0 Paper roll near-end sensor : paper adequate.
0, 1
On 03 3 Paper roll near-end sensor : paper near end.
Off
00 0 Paper roll end sensor : paper present.
2, 3
On 0C 12 Paper roll end sensor : paper not present.
4 Off 00 0 Fixed.
5 Off 00 0 Reserved.
6 Off 00 0 Reserved.
7 Off 00 0 Fixed.
- Bits 2 and 3 : This command cannot be executed since the printer
becomes offline when the paper roll end sensor detects the paper not
present. Therefore, the status of bit 2 (1) and bit 3 (1) is not transmitted.
▪ Drawer kick-out connector status (n=2, 50) :
AAWBit Off/On Hex Decimal Function
Off 00 0 Drawer kick-out connector pin 3 is LOW.
0
On 01 1 Drawer kick-out connector pin 3 is HIGH.
1 Off 00 0 Reserved.
2 Off 00 0 Reserved.
3 Off 00 0 Reserved.
4 Off 00 0 Fixed.
5 Off 00 0 Reserved.
6 Off 00 0 Reserved.
7 Off 00 0 Fixed.
GS v 0 m xL xH yL yH d1...dk
[Name]
[Format]
[Range]
Print raster bit image.
ASCII GS v 0 m xL xH yL yH d1...dk
Hex 1D 76 30 m xL xH yL yH d1...dk
Decimal 29 118 48 m xL xH yL yH d1...dk
0 ≤ m ≤ 3, 48 ≤ m ≤ 51
1 ≤ (xL + xH x 256) ≤ 128 (0 ≤ xL ≤ 128, xh=0)
1 ≤ (yL + yH x 256) ≤ 4095 (0 ≤ yL ≤ 255, 0 ≤ yH ≤ 15)
0 ≤ d ≤ 255
k = (xL + xH x 256) x (yL + yH x 256)
83
[Description] ▪ Prints a raster bit image in m mode.
- m specifies the bit image mode.
<For SRP-370>
m Mode Vertical dot density Horizontal dot density
0, 48 Normal 180 dpi 180 dpi
1, 49 Double-width 180 dpi 90 dpi
2, 50 Double-height 90 dpi 180 dpi
3, 51 Quadruple 90 dpi 90 dpi
<For SRP-372>
m Mode Vertical dot density Horizontal dot density
0, 48 Normal 203 dpi 203 dpi
1, 49 Double-width 203 dpi 203/2 dpi
2, 50 Double-height 203/2 dpi 203 dpi
3, 51 Quadruple 203/2 dpi 203/2 dpi
dpi : dots per 25.4mm {1"}
- xL, xH specifies (xL + xH x 256) byte(s) in the horizontal direction for the bit image.
- yL, yH specifies (yL + yH x 256) dot(s) in the vertical direction for the bit image.
- d specifies the definition data of the bit image data.
GS w n
[Name]
[Format]
[Range]
[Description]
[Notes]
Set bar code width.
ASCII GS w n
Hex 1D 77 n
Decimal 29 119 n
2 ≤ n ≤ 6
n=3
▪ Set the horizontal size of the bar code, using n as follows :
<For SRP-370>
Binary-level Bar Code
n
Multi-level Bar Code
Module Width (mm)
Thin element width (mm) Thick element width (mm)
2 0.282 0.282 0.706
3 0.423 0.423 1.129
4 0.564 0.564 1.411
5 0.706 0.706 1.834
6 0.847 0.847 2.258
<For SRP-372>
Binary-level Bar Code
n
Multi-level Bar Code
Module Width (mm)
Thin element width (mm) Thick element width (mm)
2 0.250 0.250 0.626
3 0.375 0.375 1.001
4 0.500 0.500 1.251
5 0.626 0.626 1.627
6 0.751 0.751 2.002
▪ Multi-level bar codes are as follows :
- UPC-A, UPC-E, JAN13, HAN8, CODE93, CODE128
▪ Binary-level bar codes are as follows :
- CODE39, ITF, CODABAR