Samsung 2 COLOR THERMAL PRINTER SRP-370, User Manual

Page: 32 / 45

62
▪ When a=8, the memory switch 8 is set as follows :
Bit Setting value Function
1~8 Reserved.
▪ When a=9, the memory switch 9 is set as follows :
Bit Setting value Function
48 Data Length : 8 Bits 2
49 Data Length : 7 Bits
48 Parity : odd 3
49 Parity : even
48 Parity Check : Disable 4
49 Parity Check : Enable
48 Flow Control : DTR/DSR 5
49 Flow Control : XON/XOFF
6~8 Baud Rate Selection.
MSW9-8 MSW9-7 MSW9-6 Baud Rate
48 48 48 9600
48 48 49 19200
48 49 48 38400
48 49 49 57600
49 48 48 115200
<Function 4>
GS ( E pL pH fn a (fn=4)
[Format]
[Range]
[Description]
ASCII GS ( E pL pH fn a
Hex 1D 28 45 pL pH fn a
Decimal 29 40 69 pL pH fn a
(pL + pH x 256) = 2 (pL=2, pH=0)
fn=4
a=1, 2, 8
▪ Transmits the setting value(s) of the memory switch specified by a.
Hexadecimal Decimal Amount of Data
Header 37H 55 1 byte
Flag 21H 33 1 byte
Data 30H or 31H 48 or 49 8 bytes
NUL 00H 0 1 byte
▪ Data for the setting is transmitted as 8 bytes or a data string in the order
from bit 8 to bit 1, as follows :
- Off : Hexadecimal = 30H / Decimal = 48
- On : Hexadecimal = 31H / Decimal = 49
63
<Function 11>
GS ( E pL pH fn a d1...dk (fn=11)
[Format]
[Range]
[Default]
[Description]
[Notes]
ASCII GS ( E pL pH fn a d1...dk
Hex 1D 28 45 pL pH fn a d1...dk
Decimal 29 40 69 pL pH fn a d1...dk
3 ≤ (pL + pH x 256) ≤ 65535 (0 ≤ pL ≤ 255, 0 ≤ pH 255)
fn=11
1 ≤ a ≤ 4
48 ≤ d ≤ 57
1 ≤ k ≤ 6
▪ When a=1 : (d1...dk)="19200"
▪ When a=2 : d=48
▪ When a=3 : d=48
▪ When a=4 : d=56
▪ Sets the communication conditions of the serial interface specified by a
according to value d.
a Communication Condition d
1 Baud rate k bytes of (d1...dk)
2 Parity 1 byte of (d1)
3 Flow control 1 byte of (d1)
4 Data length 1 byte of (d1)
- Baud rate setting (d1...dk)
Baud rate
(bps)
d1 d2 d3 d4 d5 d6
2400 50 52 48 48 -- --
4800 52 56 48 48 -- --
9600 57 54 48 48 -- --
19200 49 57 50 48 48 --
38400 51 56 52 48 48 --
57600 53 55 54 48 48 --
115200 49 49 53 50 48 48
- Parity setting (d1)
d1 Parity
48 No parity
49 Odd parity
50 Even parity
- Flow control setting (d1)
d1 Flow control
48 DTR / DSR
49 XON / XOFF
- Data length setting (d1)
d1 Data length
55 7 bits
56 8 bits
▪ If the value specified with a, d1 is out of range, this command is ignored.
(The setting is not changed)
▪ This function code fn=11 is enabled only in the user setting mode.