Sakai SV201-1 Shop Manual Download Page 162

Page: 162 / 238

8-008

INSPECTION AND ADJUSTMENT

6. MEASUREMENT AND INSPECTION OF STEERING

CIRCUIT PRESSURE

6-1. Measurement

WARNING

Make sure that there is no person around the articulated
portion of the machine before operating the steering
wheel.

Oil temperature during measurement : 50

± 5

°C (122

± 41

°F)

①

Disconnect hose (1) from vibrator·steering pump. Attach

pressure gauge through the adapter

ⓝ

Adapter

ⓝ

: G3/8

Pressure gauge : 0 to 25 MPa (0 to 3,625 psi)

②

Confirm that F-R lever is in “N” properly.

③

Set steering wheel to a position where vibratory drum
faces straight forward.

④

Start the engine and set throttle lever to “FULL”.

⑤

Turn steering wheel to operate relief valve.

Then, read pressure indicated by pressure gauge.

Standard maximum circuit pressure
(orbitroll relief pressure)

: 11.8

± 1.0

MPa (1,711

± 145

psi)

•

•
•

•

★

SV201-1-08017

PG002003

Summary of Contents for SV201-1















































































































































































































































Search results

Summary of Contents for SV201-1

Reviews:

Related manuals for SV201-1

Brands by name

Popular brands

Sakai SV201-1, Shop Manual

Search results

Summary of Contents for SV201-1

Reviews:

Related manuals for SV201-1

Brands by name

Popular brands