Saab 2002 9-5 2.3 Turbo Ecopower Owner'S Manual Download Page 23 | Manualshive

Page: 23 / 272

background image

23

Safety

Child tether anchorages for forward

facing child car seats

Child restraints with a tether strap must be
anchored according to Canadian and USA
laws.
If you have any questions regarding child
tether anchorages please contact your
Saab dealer.

9-5 Sedan:

1 Open the cover that is right behind the

child restraint. Make sure it locks.

2 Place the child restraint in the rear seat.
3 Secure the lower part of the child

restraint by means of the lower anchor-
ages (ISOFIX) or the safety belts as
described in the child restraint mounting
instruction.

4 Route the tether under the headrest.
5 Attach the tether to the anchorage.
6 Tighten the tether so that the back of the

child restraint is pressed hard against
the backrest.

7 Pull the child restraints to make a

second check that the restraints are
securely attached at both the lower
anchorages bars and the top tether
strap.

WARNING

Child tether anchorages are designed to
withstand only those loads imposed by
correctly fitted child restraints.

Under no circumstances are they to be
used for adult safety belts.

IB1698

Child tether anchorages in parcel shelf,
Saab 9-5 Sedan

«
...
21
22
23
24
25
...
»

Summary of Contents for 2002 9-5 2.3 Turbo Ecopower

















































































































































































































































































Reviews:

No comments

Related manuals for 2002 9-5 2.3 Turbo Ecopower

Brand: Kargo Master Pages: 5

Brand: Ford Pages: 22

Brand: Mazda Pages: 720

Brand: Alfa Romeo Pages: 8

Sprinter Side Ladder

Brand: FVC Pages: 8

Brand: Oypla Leisure Pages: 4

Brand: Honda Pages: 124

Brand: Carcomm Pages: 2

Brand: Toyota Pages: 497

Brand: Huf Pages: 6

Brand: KLAUS Multiparking Pages: 72

CHALLENGER GK-6125A 2018

Brand: Coolster Pages: 45

Brand: P-Charge Pages: 16

Cutlass 1978 Series

Brand: Oldsmobile Pages: 97

Brand: LAS Pages: 10

Brand: Steinhof Pages: 2

Brand: Chrysler Pages: 374

Brand: Honda Pages: 435

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands