Saab 2002 9-5 2.3 Turbo Ecopower Owner'S Manual Download Page 211

Page: 211 / 272

211

Car care and technical information

Reassembly:

1 Place the two ”hinges” in the recess in

the tailgate.

2 Then push the ”hinges” into the recess

and close the cover.

3 Turn the lock a quarter turn.

Rear lights clusters, 9-5 Wagon

1 Open the tailgate.
2 Remove the cover by turning the two

catches anticlockwise one quarter turn.

3 Remove the two screws securing the

light cluster to the body.

4 Pull the light cluster rearwards and

angle it outwards (it is seated quite
firmly).

5 Release the fastener from the body.

Reinsert the fastener into the groove in
the light cluster. Press in the fastener
until you hear a click.

6 Take out the bulb holder by twisting it

slightly counterclockwise.

7 Press in the bulb and twist it counter-

clockwise.

8 Change the bulb.
9 Check that the new bulb works.

IB1228

IB1881

IB1793

Summary of Contents for 2002 9-5 2.3 Turbo Ecopower

















































































































































































































































































Search results

Summary of Contents for 2002 9-5 2.3 Turbo Ecopower

Reviews:

Related manuals for 2002 9-5 2.3 Turbo Ecopower

Brands by name

Popular brands

Saab 2002 9-5 2.3 Turbo Ecopower, Owner'S Manual

Search results

Summary of Contents for 2002 9-5 2.3 Turbo Ecopower

Reviews:

Related manuals for 2002 9-5 2.3 Turbo Ecopower

Brands by name

Popular brands