Saab 2002 9-5 2.3 Turbo Ecopower Owner'S Manual Download Page 208

Page: 208 / 272

208

Car care and technical information

Front turn signal bulbs

To change the bulb, the complete lamp unit
has to be removed.

1 Depress the catch, accessed from the

engine bay.

2 Carefully pull out the lamp unit.
3 The bulb holder has a bayonet fitting.

Grip the holder and twist it counterclock-
wise.

4 Withdraw the bulb holder from the lamp

unit.

5 The bulb also has a bayonet fitting.

Press in the bulb and twist it counter-
clockwise.

6 Fit the new bulb and check that it is cor-

rectly seated.

To re-install the lamp unit

1 Align the catch with the recess in the

lamp housing holder.

2 Press the lamp housing towards the

headlight slightly and press the housing
towards the rear of the car.

3 Make sure the locating pin and the two

plastic lugs enter their respective holes.

4 Press the lamp housing until it click into

place.

IB1789

Front turn signal bulb

1 Catch
2 Bayonet pin
3 Plastic lugs

IB1875

Catch seen from engine bay, left-hand
side

IB1876

Catch seen from engine bay, right-hand
side

IB1790

Summary of Contents for 2002 9-5 2.3 Turbo Ecopower

















































































































































































































































































Search results

Summary of Contents for 2002 9-5 2.3 Turbo Ecopower

Reviews:

Related manuals for 2002 9-5 2.3 Turbo Ecopower

Brands by name

Popular brands

Saab 2002 9-5 2.3 Turbo Ecopower, Owner'S Manual

Search results

Summary of Contents for 2002 9-5 2.3 Turbo Ecopower

Reviews:

Related manuals for 2002 9-5 2.3 Turbo Ecopower

Brands by name

Popular brands