RYTEC Spiral SST Installation Manual Download Page 7

Page: 7 / 36

Spiral

SST and STT Prewire Installation Manual

Spiral

SST and STT Prewire Installation Manual

■

1072124-0

■

Rev 03

■

01/22

-S and -S/R doors: look for

the wall mount brackets at the top rear corners of the head assembly.

Remove

the screws and washers and

flip

each bracket so the flange points up.

Line up

bracket with the rear of the head assembly, then

reinstall

the screws and washers.

On the non-drive (controller) side,

reach

into the

console and place the two cables with junction boxes

on top of the head assembly.

Make sure

as much of the cables as possible are clear

of the side columns (non-shaded area).

Leave the pulley, spring strap and other cabling

place.

In both consoles,

look for the preinstalled

CAN connector(s) (unattached cable with M12

connector descending from wire chase).

If the cable hangs below the bottom of the head

assembly (dotted line),

use a cable tie

to keep it

clear of the bottom.

Brackets are labeled
with yellow tags.

Remove tags

before

flipping brackets.

Rear screws connect
to

flanged nuts

Front screws connect
to

riveted nuts

STT-S

Full vision doors have a spacer

at the rear of the head assembly.

Line up bracket

with spacer.

Solid panel doors

have no spacer.

SST-S/R

If the door has a slanted top hood
cover,

do not reinstall

the outer

screws and washers until the
cover is installed.

13mm

Cutting

pliers

Protect your cables!

Make sure

all cables preinstalled in the head assembly are clear of the side columns

and won’t get pinched or crushed when the head assembly is installed.

Cable ties

Unscrew

the retaining nut, cut the cable tie

and slide the cable through the hole in the console.

Slide the nut

up the cable and reattach.

Coil the cable

inside the console.

Remove

the five preinstalled side column screws

(located in the non-shaded area).

Do this

on both sides of the head assembly.

Before lifting the head assembly,

clamp both forks

so the

fork pockets are secure.

10mm

Protect the brake release cable!

The cable is preinstalled, and can be

damaged when the head assembly

is raised onto the side columns. This

extra step puts it out of harm’s way.

17mm

KEEP

REUSE

C-clamp (2)

WARNING

Do not lift the head assembly

unless it has been clamped or

secured to both forks of the forklift.

Summary of Contents for Spiral SST





































Search results

Summary of Contents for Spiral SST

Reviews:

Related manuals for Spiral SST

Brands by name

Popular brands

RYTEC Spiral SST, Installation Manual

Search results

Summary of Contents for Spiral SST

Reviews:

Related manuals for Spiral SST

Brands by name

Popular brands