RYTEC Spiral SST Installation Manual Download Page 34

Page: 34 / 36

Spiral

SST and STT Prewire Installation Manual

Spiral

SST and STT Prewire Installation Manual

■

1072124-0

■

Rev 03

■

01/22

How to level the baseplate pulley assembly

Loosen

the screws and

move

the CAN bracket out

of the way to access the pulley assembly.

Loosen

the top nut of the bolt on the side opposite to the side the belt favors

Lower

the bolt until it touches the baseplate.

Turn the bolt

one more half-turn

to raise that side of the pulley assembly, then test the door.

Manually raise and lower

the door three (3) times.

If the belt is not centered in the pulley assembly:

repeat these steps and retest.

If the belt is centered:

raise the lower nut

to lock the assembly in place.

Reinstall

the CAN bracket when you are done.

13mm

Loosen

this nut

Lower

this bolt

Loosen

this nut

Belt

misaligned

to the left

Lower

this bolt

Belt

misaligned

to the right

Lower

the bolt on the side

opposite to the misaligned belt.

13mm

Raise

nut

13mm

How to manually reset the close limit (optional)

First: set the controller to Parameter mode and access Service level parameters

Do This

Result

You are in Parameter mode. Go to parameter 999.

The Password parameter P:999 screen displays.

You can now change the value of parameter P:999.

Do This

Result

Set the value to 10 (Service level password).

The Service level password is saved.

You can now go to parameter 275.

Next: navigate to parameter P:275 (parameter P:221 for doors with photo eyes) and change the value

Do This

Result

The default value is -12 (default at.

You can now change the value.

▪

The UP arrow

increases the value and raises the

close limit position for the door.

▪

The Down arrow

decreases the value and lowers

the close limit for the door.

▪

Each press of an arrow changes the limit by

a fraction of an inch, which gives you precise

control of the value.

Do This

Result

Do not change the value by more than

10 increments. Then test the door.

The new value is saved.

001=

[xxx] Cyc

P:Password

until the parameter screen displays

RY-UI-000050

PDN-UI-000051

999=

0000

P:Password

to reach parameter P:999

PDN-UI-000052

to move cursor to the right (edit value)

0000

999=

P:Password

PDN-UI-000059

999=

0010?#

P:Password

16x

to set value to hexadecimal 10

PDN-UI-000060

until question mark changes to

checkmark (value saved)

999=

0010

P:Password

PDN-UI-000061

to move cursor to left (parameters)

999=

0010

P:Password

PDN-UI-000057

275=

-12

Inc

P:Incremental

until parameter displays

PDN-UI-000052

to move cursor to the right (edit value)

275=

-12

Inc

P:Incremental

PDN-UI-000059

until new value displays

275=

[x]?Inc

P:Incremental

PDN-UI-000060

until question mark changes to

checkmark (value saved)

275=

[x]

Inc

P:Incremental

PDN-UI-000060

until door returns to run mode

Spiral

[xxx] Cycles

Summary of Contents for Spiral SST





































Search results

Summary of Contents for Spiral SST

Reviews:

Related manuals for Spiral SST

Brands by name

Popular brands

RYTEC Spiral SST, Installation Manual

Search results

Summary of Contents for Spiral SST

Reviews:

Related manuals for Spiral SST

Brands by name

Popular brands