RYTEC Spiral SST Installation Manual Download Page 22

Page: 22 / 36

Spiral

SST and STT Prewire Installation Manual

Spiral

SST and STT Prewire Installation Manual

■

1072124-0

■

Rev 03

■

01/22

(Optional) How to install BTA4 user terminal in a remote location

Locate

the BTA4 kit and

cable in the small parts box.

If you are mounting the unit to the wall and

cannot run cable inside the wall,

snap off

the

perforated tab at the bottom of the frame.

Install

the BTA4 frame using the supplied

hardware or your own.

Plug

the female quick connector on the cable into the

back of the BTA4 unit.

ID Part No.

Description

Qty.

1210765-0

BTA4 unit

1210766-0

BTA4 frame

5550351-0A01 Mounting hardware,

5550057-0Z01 side column

1210756-0

Mounting hardware,

5550353-0 wall

SMALL PARTS

1210800

Line up

the two bottom tabs

on the BTA4 unit with the

bottom tabs in the frame

Then

snap

the two top

tabs into place

In the head assembly, on the drive side,

remove

the jumper from port 1 on the CAN repeater

and

plug in

the cable from the BTA4 terminal

▪

This port requires the least amount of cable routing to connect the remote BTA4 to the CAN bus.

The BTA4 user terminal will

automatically sync with the controller

when you manually sync the light curtains.

See

How to sync the SmartSurround™ system to the controller, set limits, and test the door

beginning on page 28.

Summary of Contents for Spiral SST





































Search results

Summary of Contents for Spiral SST

Reviews:

Related manuals for Spiral SST

Brands by name

Popular brands

RYTEC Spiral SST, Installation Manual

Search results

Summary of Contents for Spiral SST

Reviews:

Related manuals for Spiral SST

Brands by name

Popular brands