RYTEC Spiral SST Installation Manual Download Page 33

Page: 33 / 36

Spiral

SST and STT Prewire Installation Manual

Spiral

SST and STT Prewire Installation Manual

■

1072124-0

■

Rev 03

■

01/22

How to adjust the proximity sensor

What’s the problem?

The controller tracks the position of the manual break release through a magnetic sensor located

in the motor. In some installation environments, the sensor needs to be adjusted from the factory preset to correctly

track the brake release.

WARNING

Do not perform this procedure

until the power disconnect is in

the OFF position and a lockout/tagout is complete.

Contact with high-voltage wires, or the door being activated
unexpectedly,

can cause death or serious injury.

At the motor,

remove

the brake release

lever.

DO NOT

remove the cable. The play in the

spring allows it to turn with the release

lever until it is free of the motor.

F211 E-Stop Ext1

Emergency Stop

Door

Stopped

F211 E-Stop Ext1

Emergency Stop

Lever down:

brake released

Lever up:

brake reset

Controller

No action is needed

Reset the sensor

10mm

Remove

the four screws and the

bottom cover of the motor.

Check

the distance between the sensor and the brake release arm

It should be .03”/.76mm, which is the

thickness of a credit card.

To adjust the sensor, first

loosen

the outer nut

, then

tighten

the inner nut

to secure it in place.

Test

the manual brake release again.

If the controller displays the F211 error on reset,

repeat these steps and retest.

If the controller displays “Door Held Open”,

the issue is resolved.

Reinstall

the motor cover and the brake release lever.

KEEP

REUSE

0.03" / 0.76 mm

17mm

Summary of Contents for Spiral SST





































Search results

Summary of Contents for Spiral SST

Reviews:

Related manuals for Spiral SST

Brands by name

Popular brands

RYTEC Spiral SST, Installation Manual

Search results

Summary of Contents for Spiral SST

Reviews:

Related manuals for Spiral SST

Brands by name

Popular brands