RYTEC Spiral SST Installation Manual Download Page 29

Page: 29 / 36

Spiral

SST and STT Prewire Installation Manual

Spiral

SST and STT Prewire Installation Manual

■

1072124-0

■

Rev 03

■

01/22

Next: begin the SmartSurround™ system synchronization

Do This

Result

Check the Advanced

light curtains mounted in

the door tracks of both side columns.

▪

If all four LEDs are flashing (transmitter: green

and yellow, receiver: blue and red), the door track

light curtains are synced correctly.

▪

If other light curtains light up, go to the next value.

If the current selection does

NOT light

the LEDs:

Re-check

the light curtains.

Do This

Result

If the current selection

DOES light

the LEDs:

The controller moves to parameter L:401.

Check the SmartSurround™ cover mounted

(front) light curtains on both side columns.

▪

If all LEDs are flashing, the cover mounted light

curtains are synced correctly.

▪

If other light curtains light up, go to the next value.

PDN-UI-000052

to show the first set of light curtains

201= 0932-9156?

L:SAI

Slot2

Drive side

Non-drive side

PDN-UI-000059

to show the next set of light curtains

201= 0948-9147?

L:SAI

Slot2

PDN-UI-000060

201= 0948-9147

L:SAI

Slot2

until the setting is saved

401=

L:SAI Slot4

PDN-UI-000052

to show the first set of light curtains

401= 0932-9156?

L:SAI

Slot4

Drive side

Non-drive side

Do This

Result

If the current selection does

NOT light

the LEDs:

Re-check

the light curtains.

If the current selection

DOES light

the LEDs:

The controller moves to parameter L:501.

Do This

Result

Check the SmartSurround™ wall mounted

(rear) light curtains on both side columns.

▪

If all LEDs are flashing, the cover mounted light

curtains are synced correctly.

▪

If other light curtains light up, go to the next value.

If the current selection does

NOT light

the

LEDs:

Re-check

the light curtains.

If the current selection

DOES light

the LEDs:

The controller ends at parameter P:000.

PDN-UI-000059

to show the next set of light curtains

401= 0992-9187?

L:SAI

Slot4

PDN-UI-000060

401= 0992-9187

L:SAI

Slot4

until the setting is saved

501=

L:SAI Slot5

PDN-UI-000052

to show the first set of light curtains

501= 0932-9156?

L:SAI

Slot5

Drive side

Non-drive side

PDN-UI-000059

to show the next set of light curtains

501= 0923-9126?

L:SAI

Slot5

PDN-UI-000060

501= 0923-9126

L:SAI

Slot5

until the setting is saved

000#

0000

Cyc

P:Door

Cycles

Summary of Contents for Spiral SST





































Search results

Summary of Contents for Spiral SST

Reviews:

Related manuals for Spiral SST

Brands by name

Popular brands

RYTEC Spiral SST, Installation Manual

Search results

Summary of Contents for Spiral SST

Reviews:

Related manuals for Spiral SST

Brands by name

Popular brands