background image

4 - English

 

During normal use the tool will recoil immediately 
after driving a fastener. This is a normal function of 
the tool. 

Do not attempt to prevent the recoil by holding 

the nailer against the work. Restriction to the recoil can 
result in a second fastener being driven from the nailer. 
Grip the handle firmly and let the tool do the work. Failure 
to heed this warning can result in serious personal injury.

 

Do not drive fasteners on top of other fasteners or with 
the tool at an overly steep angle as this may cause 
deflection of fasteners which could cause injury.

 

Do not drive fasteners close to the edge of the 
workpiece as the wood may split, allowing the fas-
tener to be deflected possibly causing injury.

 

AIR SUPPLY AND CONNECTIONS

 

Do  not  use  oxygen,  combustible  gases  or  bottled 

gases as a power source for this tool as tool will ex-
plode, possibly causing injury or death.

 

Do not use with an air compressor which can po-
tentially exceed 200 psi as tool may burst, possibly 
causing injury. 

 

The connector on the tool must not hold pressure 
when air supply is disconnected.  

If an incorrect fitting 

is used, the tool can remain charged with air after discon-
necting and thus will be able to drive a fastener even after 
the air line is disconnected, possibly causing injury.

 

Always disconnect air supply:

•  Before making adjustments
•  When servicing the tool
•  When clearing a jam
•  When tool is not in use
•  When moving to a different work area, as accidental 

actuation may occur, possibly causing injury.

LOADING TOOL

 

Do not load the tool with fasteners when any one of 

the operating controls is activated.

When loading tool: 

 

Never place a hand or any part of body in fastener 
discharge area of tool.

 

Never point tool at anyone.

 

Do not pull the trigger or depress the workpiece 
contact as accidental actuation may occur, possibly 
causing injury.

SAVE THESE INSTRUCTIONS

 

Refer to them frequently and use them to instruct others 
who may use this tool. If you loan someone this tool, loan 
them these instructions also.

SPECIFIC SAFETY RULES

CALIFORNIA PROPOSITION 65

WARNING: 

This product and some dust created by power sanding, sawing, grinding, drilling, and other construction activities may 

contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other reproductive 

harm. 

Wash hands after handling.

Some examples of these chemicals are:
 

•  lead from lead-based paints,

 

•  crystalline silica from bricks and cement and other masonry products and,

 

•  arsenic and chromium from chemically treated lumber. 

Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your 
exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially 
designed to filter out microscopic particles. 

Summary of Contents for YG200BN





































Reviews: