background image

8 — English

ASSEMBLY

INSTALLING THE HANDLE ASSEMBLY

See Figures 2 - 3.

  Place the lower handle onto the bar on the cultivator.

 

NOTE:

 The bar should fit inside the grooves in the lower 

handle.

  Align the holes in the lower handle with the holes in the 

bar, and secure using bolts and knobs. Tighten knobs 
securely.

  Place the upper handle onto the lower handle.

 

NOTE:

 The lower handle should fit inside the grooves in 

the upper handle.

  Align the holes in the lower handle with the holes in the 

upper handle, and secure using bolts and knobs. Tighten 
knobs securely.

FOLDING/UNFOLDING THE HANDLE 
ASSEMBLY

See Figures 4 - 5.

To fold handle assembly:

  Loosen the knobs on the upper handle.

  Fold the upper handle down and back onto the lower 

handle.

 NOTE:

 Do not use force. If there is binding, continue to 

loosen the knobs. Do not allow the switch trigger cable 
to become pinched when lowering the handle.

  Loosen the knobs on the lower handle.

  Push the upper and lower handles forward and down 

onto the cultivator.

To unfold handle assembly:

  Pull the lower handle up and back until it is aligned with 

the bar on the cultivator.

 

NOTE:

 The bar should fit inside the grooves in the lower 

handle.

  Tighten the knobs on the lower handle, to secure it in 

place.

  Pull the upper handle up and forward until it is aligned 

with the lower handle.

 

NOTE:

 The lower handle should fit inside the grooves in 

the upper handle.

  Tighten the knobs on the upper handle, to secure it in 

place.

WARNING:

Be certain the knobs are fully tightened before operating 
equipment; check them periodically for tightness during 
use to avoid serious personal injury.

INSTALLING THE TINES

See Figures 6 - 10.

The inner tine assemblies are marked “A”. The right outer 
tine is marked “C” and the left outer tine is marked “B”. For 
correct operation of the unit, the tines must be installed in 
the correct position.

  Place the inner tine assemblies on the tine shaft as shown. 

  Rotate the tine assemblies until the holes in the assemblies 

are aligned with the holes in the tine shaft.

 

NOTE:

 If the holes do not align, the tine assemblies may 

be installed on the wrong sides. Reverse the position of 
the tine assemblies and check for hole alignment. When 
installed correctly, the “A” on the right inner tine assembly 
should be closer to the gear box than the “A” on the left 
inner tine assembly.

  Insert lock pins through the holes in the tine assemblies 

and the shaft.

  Pull the band on each lock pin around the tine shaft and 

connect them to the the bottom of each pin.

  Place the outer tine marked “C” on the right side of the 

tine shaft and the outer tine marked “B” on the left side 
of the shaft. 

  Rotate the outer tines until the holes in the tines are 

aligned with the holes in the tine shaft.

  Install lock pins and secure the outer tines in place.

INSTALLING THE WHEELS

See Figure 11.

Wheels are provided to assist in moving the unit to and from 
the work area. 

To install:

  Slide a wheel onto the axle.

  Slide a washer onto the axle until it touches the wheel.

  Insert a hitch pin to secure.

 

NOTE:

 The hitch pin should be pushed into the axle until 

the center of the pin rests on top of the axle.

  Push the end cap into the center of the wheel until it snaps 

into place.

  Repeat with the second wheel.

Summary of Contents for RYAC701











































Reviews: