GB
E
E
GB
To start a cold engine:
DO NOT
squeeze the throttle trigger until the engine
starts and runs.
n
lay
the trimmer on a flat, bare surface.
n
PRIME
- Press the primer bulb 10 times.
n
SET
the start lever to the
STaRT
position.
n
PUll
the rope quickly and sharply straight up until
the engine starts.
n
Wait 6-10 seconds, then squeeze the trigger to run.
NOTE:
Squeezing and releasing the throttle trigger
releases the start lever to the
RUN
position.
To start a warm engine:
PUll
the rope quickly and sharply straight up until the
engine starts.
To stop the engine:
Press and hold the switch in the stop “
O
” position until
the engine stops.
OPERaTInG THE TRIMMER (Fig. 5)
Hold the trimmer with the right hand on the rear handle
and the left hand on the front handle. Keep a firm grip
with both hands while in operation. Trimmer should be
held at a comfortable position with the rear handle about
hip height.
always operate trimmer at full throttle.
Cut tall grass
from the top down. This will prevent grass from wrapping
around the shaft housing and bump head which may
cause damage from overheating. If grass becomes
wrapped around the bump head, stop the engine,
disconnect the spark plug wire, and remove the grass.
Prolonged cutting at partial throttle will result in lubricant
dripping from the silencer.
CUTTInG TIPS (Fig. 6)
aDVanCInG THE lInE (Fig. 7)
For
Reel Easy
TM
(RLT0CESNB).
MaInTEnanCE
WaRnInG
Use only original manufacturer's replacement
parts, accessories and attachments. Failure to
do so can cause possible injury, poor perfor-
mance and may void your warranty.
n
You may make adjustments and repairs described
here. For other repairs, have the trimmer serviced by
an authorised service agent.
n
Consequences of improper maintenance may
include excess carbon deposits resulting in loss of
performance and discharge of black lubricant residue
dripping from the muffler.
n
Make sure all guards, straps, deflectors and handles
are properly and securely attached to avoid the risk of
personal injury.
n
For RlT30CESnB:
the cutting attachment must not
work in idle mode. If this requirement is not satisfied,
the clutch has to be adjusted or the machine needs
an urgent maintenance by a qualified technician.
lInE REPlaCEMEnT
For Pro Cut II
TM
(RLT0CDNB
&
RLT0CESNB).
(Fig. 2 )
For
Reel Easy
TM
(RLT0CESNB).
(Fig. 8 )
ClEanInG THE EXHaUST PORT anD MUFFlER
Depending on the type of fuel used, the type and amount
of lubricant used, and/or your operating conditions, the
exhaust port and muffler may become blocked with
carbon deposits. If you notice a power loss with your
petrol powered tool, a qualified service technician will
need to remove these deposits to restore performance.
SPaRK aRRESTOR
The spark arrestor must be cleaned or replaced every
25 hours or yearly to ensure proper performance of
your product. Spark arrestors may be in different locations
depending on the model purchased. Please contact
your nearest service dealer for the location of the spark
arrestor for your model.
ClEanInG THE aIR FIlTER SCREEn (Fig. 9)
For proper performance and long life, keep air filter
screen clean.
n
Remove the air filter cover by pushing down on the latch
with your thumb while gently pulling on the cover.
n
Brush the air filter screen lightly to clean.
n
Replace the air filter cover by inserting the tabs on the
bottom of the cover into the slots on the air filter base;
push the cover up until it latches securely in place.
FUEl CaP
WaRnInG
A leaking fuel cap is a fire hazard and must be
replaced immediately.
The fuel cap contains a non-service able filter and a
check valve. A clogged fuel filter will cause poor engine
performance. If performance improves when the fuel cap
is loosened, check valve may be faulty or filter clogged.
Replace fuel cap if required.
7
English
