![background image](http://html1.mh-extra.com/html/ryobi/etms-1425/etms-1425_user-manual_1506473016.webp)
SAFETY INSTRUCTIONS
■
Do not leave the saw in the rain and never use it in
damp or wet conditions.
■
Provide good lighting.
■
Never saw near combustible liquids or gases.
■
Wear suitable work clothes! Loose garments or
jewellery may become caught up in the rotating
saw blade.
■
Operators have to be at least 18 years of age.
Trainees of at least 16 years of age are allowed to
use the machine only under supervision.
■
Keep children away from the machine when it is
connected to the power supply.
■
Check the power cable. Never use a faulty or
damaged power cable.
■
Keep your workplace clean of wood scrap and any
unnecessary objects.
■
Persons working on the machine should not
be distracted.
■
Note the direction of rotation of the motor and
saw blade.
■
After you have switched off the motor, never slow
down the saw blade by applying pressure to its side.
■
Fit only blades which are well sharpened and have no
cracks or deformations.
■
The machine is to be operated only with tools which
conform with EN 847-1: 1996.
■
Faulty saw blades have to be replaced immediately.
■
Never use saw blades which do not comply with the
data specified in this manual.
■
Make sure that the arrow on the saw blade complies
with the arrow marked on the machine.
■
Make certain that the saw blade does not touch the
turntable in any setting. To do so, pull out the power
plug and tilt the saw blade by hand into the
45° position and the 90° position. If necessary,
re-adjust the saw head.
■
It is imperative to make sure that all the devices used
to cover the saw blade are in good working order.
■
Never wedge the hinged guard hood in open position.
■
Never dismantle the machine’s safety devices or put
them out of operation.
■
Damaged or faulty safety devices have to be replaced
immediately.
■
Never cut workpieces which are too small to hold
securely in your hand.
■
Do not place your hands in awkward positions where
one or both may slip suddenly and touch the saw blade.
■
When working with long workpieces, use an
additional support (table, stand, etc.) to prevent the
machine from tipping over.
■
Always clamp round workpieces such as dowel
rods etc. with suitable devices.
■
There must be no nails or other foreign bodies in that
part of the workpiece you want to cut.
■
Always stand to the side of the saw blade when
working with the saw in mitre saw mode.
■
Never load the machine so much that it cuts out.
■
Always press the workpiece firmly against the table
and the stop rail to prevent it from wobbling or twisting.
■
Make sure that off-cuts can be removed from the
side of the saw blade. If not, they may catch on the
saw blade crown and be catapulted into the
surrounding area.
■
Never saw several workpieces simultaneously.
■
Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
■
To rectify faults or remove jammed pieces of wood,
always switch off the machine first.
Pull out the
power plug!
■
Conversions, adjustments, measurements and
cleaning jobs are to be performed only when the
motor is switched off.
Pull out the power plug!
■
Before you switch on the machine, check that all
wrenches and adjustment tools have been removed.
■
When you leave your workplace, switch off the motor
and pull out the power plug.
■
Electric installation work, repairs and maintenance
are to be carried out only by specialists.
■
All guards and safety devices have to be refitted
immediately after completion of any repairs or
maintenance.
■
It is imperative to observe the manufacturer’s safety,
operating and maintenance instructions as well as the
dimensions quoted in the technical data.
■
It is imperative to observe the accident prevention
regulations in force in your area as well as all other
generally recognized rules of safety.
■
Note the information published by your professional
associations.
■
Switch on the dust extraction system each time you
use the machine.
■
The machine may be used in closed rooms only in
conjunction with a suitable vacuum extraction system.
■
The cross-cut saw must be connected to a 230 V
socket-outlet with a minimum 10 A fuse.
■
Never use light-duty machines for heavy-duty work.
10
GB
F
D
E
English
I
P
NL
S
DK
N
FIN
GR
H
CZ
RUS
RO
PL
ETMS-1425 manual 5/07/04 15:34 Page 10
Summary of Contents for ETMS-1425
Page 2: ...Fig 1 Fig 2 27 28 25 18 29 21 19 8 32 20 7 16 17 33 1 15 6 10 14 12 11 9 35 4 2 37 3...
Page 3: ...Fig 3 Fig 4 Fig 5 Fig 6 Fig 7 Fig 8 30 31 36 22 23 24 28 26 25 a b 3 5mm 30 15 6...
Page 4: ...Fig 9 Fig 10 Fig 11 Fig 12 Fig 13 Fig 14 26 28 25 27 18 17 16 b a 40 40 39 38...
Page 5: ...Fig 15 Fig 16 Fig 17 Fig 18 Fig 19 17 33 34 30 21 39 19 5 39...