SAFETY INSTRUCTIONS
■
Never use the cable for any purpose other than that
for which it is intended!
■
Adopt a firm standing position and keep your balance
at all times.
■
Check the tool for signs of damage!
■
Before you carry on using the tool it is imperative to
check that its safety devices and any slightly damaged
parts are working properly and in the way intended.
■
Check that the moving parts work properly and do not
jam or whether any of the parts are damaged.
■
All parts must be fitted correctly and satisfy all
conditions for the tool to work properly.
■
Unless otherwise stated in these instructions, damaged
safety devices and parts must be repaired or replaced
by experts in an approved specialist workshop.
■
Have damaged switches replaced by an authorized
service centre.
■
This tool complies with the pertinent safety regulations.
Repairs are to be carried out only by qualified
electricians using original replacement parts. The user
may suffer an accident if this condition is not observed.
■
Be careful when working in vertical mode.
CAUTION
Special care is required when making compound
mitre cuts.
■
Do not overload your tool!
■
Wear safety goggles.
■
Wear a breathing mask on dusty jobs.
■
Examine the power cable / extension cable for
damage.
■
Never use damaged or worn blades.
■
Use only blades which are recommended by the
manufacturer and comply with EN 847-1.
■
Be careful when sawing in table saw mode.
■
Table saw mode: Make sure that the saw arm is
securely locked.
■
Cross-cut saw mode: Make sure that the upper guard
is fully closed.
■
Mitre saw mode: Make sure that the saw arm is
unlocked when cutting miters.
Wear goggles
Wear ear-muffs
Wear a breathing mask
SPECIFICATION
Input
230 V ~ 50 Hz
Power rating
1400 W
Operating mode
S1
No load speed
4000 min
-1
Saw blade dimension
ø 254 x ø 30 x 3,2 mm
Blade type
40T TCT
Connector for dust extractor
ø 39.5 mm
Standing area
500 x 500 mm
AS TABLE SAW
Upper saw table
426 x 340 mm
Cutting height
40 mm
parallel stop swinging range
-45° to +45°
AS MITRE SAW
Bevel range
0° - 45° left
Mitre cuts
0° to 45° left
Lower saw table
475 x 150 mm
Cutting depth
Mitre x Bevel:
0º x 0º
70 x 127 mm
45º L x 0º
70 x 85 mm
0º x 45º
38 x 127 mm
45º L x 45º
35 x 55 mm
DESCRIPTION
1. Release
button
2. Handle
3. On/Off switch for mitre saw mode
4. On/Off switch for table saw mode
5. Saw
blade
6. Lower guard, hinged
7. Back
fence
8. Mitre
table
9. Lower saw table stand
10. Mitre lock knob for turntable
11. Scale
12. Table insert, bottom
14. Catch
15. Changeover handle
16. Saw table
17. Upper saw blade guard
18. Parallel / Mitre stop
19. Hexagon wrench
20. Workpiece supports
21. Face wrench
22. Bevel lock knob
23. Retaining pin
25. Knurled screw for mitre settings
26. Knurled screw
27. Stop rail
11
GB
F
D
E
English
I
P
NL
S
DK
N
FIN
GR
H
CZ
RUS
RO
PL
ETMS-1425 manual 5/07/04 15:34 Page 11
Summary of Contents for ETMS-1425
Page 2: ...Fig 1 Fig 2 27 28 25 18 29 21 19 8 32 20 7 16 17 33 1 15 6 10 14 12 11 9 35 4 2 37 3...
Page 3: ...Fig 3 Fig 4 Fig 5 Fig 6 Fig 7 Fig 8 30 31 36 22 23 24 28 26 25 a b 3 5mm 30 15 6...
Page 4: ...Fig 9 Fig 10 Fig 11 Fig 12 Fig 13 Fig 14 26 28 25 27 18 17 16 b a 40 40 39 38...
Page 5: ...Fig 15 Fig 16 Fig 17 Fig 18 Fig 19 17 33 34 30 21 39 19 5 39...
