background image

14  

  Technical Information 

X935-25-00 Rev 1110 V894CSH High-Security Cameras 

Technical Information 

ELECTRICAL 

 

Input 

Voltage: 

    

12 VDC

/

24 VAC ±20%, isolated input.

 

 

Current 

Rating:    

0.11 A @ 12 VDC. 

      0.18 

24 

VAC. 

 

Power Consumption:

 

1.3 W @ 12 VDC. 

 

2.1 W @ 24 VAC. 

 

Maximum Operating Distance 

@ 24 VAC

 

Wire Size (AWG) 

(Annealed Copper Wire)

Maximum Distance 

ft (m) 

20 

1068 (326) 

18 

1707 (520) 

16 

2712 (827) 

14 

4307(1312) 

12 

6859 (2091) 

 
 

Connectors: 

   

Power: 2-pin screw terminal block. 
Video: BNC on pendant cable. 

 

Certifications:  

 

 

FCC Class A; CE. 

 

OPERATIONAL 

 

Control Display: 

 

 

On-screen, menu-driven system allowing full configuration of 
camera. 

 

Tilt and Horizontal Adjustment: 

3 axis adjustment, tilt, vertical height of camera/lens and roll  
(lens may be rotated on its axis 360º). 

Lens Adjustment: 

 

 

Focus: focus lever screw. 

 

 

 

 

 

Zoom: zoom lever screw. 

 

OPTICAL 

 

Light Loss through Window:   

Negligible. 

 

Camera/Lens Specifications:   

Refer to Table 3. 

 

Summary of Contents for V894CSH

























Reviews: