Roto-Mix 425 Operator'S Manual Download Page 31

Page: 31 / 92

INSTALLING BAFFLE
(OPTIONAL)

1. Slide the baffle assembly inside

the discharge conveyor sides and

bolt to the conveyor as illustrated on

figure 14.

2. Remove the 1/2x1 HHCS to slide

the baffle closer or futher from the

discharge. Secure the position by

reinstalling this bolt.

INSTALLING SINGLE PAIR HYDRAULIC
VALVE (OPTIONAL - TRAILER MOUNT
ONLY))

1. Disconnect hoses from bracket on top of belt shield.

2. Remove bracket from PTO shield.

3. Install hydraulic valve from kit.

4. Attach two hoses to top of valve. These hoses go to

tractor.

5. Attach hoses to pressure relief block and hydraulic

conveyor motor as shown in figure 15.

6. Attach rope to valve handle and fasten to tractor in a

convenient spot.

Page 31

FIGURE 14. BAFFLE INSTALLATION

SUPPORT
BRACKET

3/8x1

HHCS &

FLANGE

SECURE BAFFLE

POSITION W/ 1/2x1 HHCS

FIGURE 15.

HYDRAULIC VALVE INSTALLATION

PRESSURE RELIEF VALVE

ON MIXER

CONVEYOR HYDRAULIC

MOTOR

CHECK VALVE

VALVE

HANDLE

TO TRACTOR

Summary of Contents for 425





























































































Search results

Summary of Contents for 425

Reviews:

Related manuals for 425

Brands by name

Popular brands

Roto-Mix 425, Operator'S Manual

Search results

Summary of Contents for 425

Reviews:

Related manuals for 425

Brands by name

Popular brands