background image

6

  If you are not completely familiar with automotive lift mainte-

nance procedures;  STOP:  Contact factory for instructions.  

To avoid personal injury, permit only qualified personnel to 

perform maintenance on this equipment.

•  Always keep bolts tight.  Check periodically.

•  Always keep lift components clean.

•  Always if oil leakage is observed, call local service represen-

tative.

•  Always if electrical problems develop, call local service repre-

sentative.

•  Daily:  Check cables and sheaves for wear.  Replace worn 

parts as required with genuine Rotary parts.

•  Daily:  Check cables and sheaves for wear.  Observe for 

frayed cable strands.  Wipe cables with a rag to detect 

hard to see small broken cable strands.  Replace cables 

showing any broken strands.  Replace worn parts as 

required with genuine Rotary parts.

•  Monthly:  Check equalizer cable tension.  Adjust 

per lift installation instructions.  If there are no 

more threads available for adjustment, replace the 

cable.  Do not use washers to stand off the nut to use 

previously used threads.

•  Monthly:  Lubricate locking latch shafts.  Push latch handle 

several times for oil to penetrate joints.

•  Every 3 Months:  Check anchor bolts for tightness

  Anchors should be torqued to 65 ft/lbs.

•  Semi-Annually:  Check fluid level of lift power unit and refill 

if required per lift installation instructions.

•  If Lift stops short of full rise or chatters, check fluid level 

and bleed both cylinders per lift installation instructions.  

•  Replace all caution, warning or safety related decals on 

the lift if unable to read or missing.  Reorder labels from 

Rotary Lift.

MAINTENANCE INSTRUCTIONS

INSPECTION and MAINTENANCE

     See ANSI/ALI ALOIM booklet for periodic 

inspection checklist and maintenance 

log sheet.

CAUTION

Lift to be used 

by trained operator

only.

©

? ?

?

CAUTION

Always use 

safety stands when 

removing or installing 

heavy components. ©

The messages and pictographs shown are generic in nature and are meant
to generally represent hazards common to all automotive lifts regardless of
specific style.

Funding for the development and validation of these labels was provided by
the Automotive Lift Institute, PO Box 33116 Indialantic, FL. 32903-3116.

They are protected by copyright.  Set of labels may be obtained from ALI or
its member companies.

ALI/WL101c

Ó

 1992 by ALI, Inc.

Authorized personnel 

only in lift area.

©

CAUTION

CAUTION

Use vehicle

manufacturer’s

lift points.

©

CAUTION

Use height extenders

when necessary 

to ensure 

good contact.

©

CAUTION

Auxiliary adapters

may reduce 

load capacity.

©

SAFETY

INSTRUCTIONS

Do not operate 

a damaged lift.

©

Read operating

and safety manuals

before using lift.

©

SAFETY

INSTRUCTIONS

The messages and pictographs

shown are generic in nature and

are meant to generally represent

hazards common to all automotive

lifts regardless of specific style.

Funding for the development and

validation of these labels was

provided by the Automotive Lift

Institute, PO Box 33116 Indialantic,

FL. 32903-3116.

They are protected by copyright.

Set of labels may be obtained from

ALI or its member companies.

  C  1992 by ALI, Inc.                   ALI/WL101s

SAFETY

INSTRUCTIONS

Proper maintenance

and inspection

is necessary

for safe operation.

c

WARNING

Clear area if vehicle 

is in danger of falling.

©

The messages and pictographs shown are generic in nature and are meant
to generally represent hazards common to all automotive lifts regardless of
specific style.

Funding for the development and validation of these labels was provided by
the Automotive Lift Institute, PO Box 33116 Indialantic, FL. 32903-3116.

They are protected by copyright.  Set of labels may be obtained from ALI or
its member companies.

ALI/WL101w

Ó

 1992 by ALI, Inc.

WARNING

Position vehicle 

with center of gravity 

midway between 

adapters.

©

WARNING

Remain clear of lift

when raising or

lowering vehicle.

©

Keep feet 

clear of lift 

while lowering.

©

WARNING

WARNING

Do not override

self-closing

lift controls.

©

WARNING

Avoid excessive

rocking of vehicle

while on lift.

c

Summary of Contents for SPO12 Hummer 5W0 Series





































Reviews: