Rotary Gate Systems SL-1000 R Page 23 Manual Download

Page: 23 / 25

Operation Indications

During normal operation, the controller’s display will indicate
current operating conditions and status.

Power-up Display

When  the  controller  powers  up,  dashes  will  show  on  the
display  for  one  second,  then  the  firmware  version  number  will
be displayed for one second.
Exiting  programming  restarts  the  controller.  The  power -up
display will show upon the restart.

Idle Condition

While the controller is idling, waiting for a command, the
display will show circulation dashes.

Last Gate Position/Condition

When the gate moves or stops, the display will show the status
for up to one minute.



Stop is displayed as



Full Close is displayed as



Full Open is displayed as



Entrapment is displayed as

Pre-Start Delay

During the pre-start delay, the display will countdown the
number of seconds remaining before the operator starts

Reverse Delay

If  the  gate  travel  direction  is  reversed  from  user  activation  or
reversing  device  and  a  reverse  delay  is  set,  the  display  will
count  down  the  delay  time  in  seconds  before  the  operator
restarts.

Run Timer

While the gate is opening or closing, the number of seconds
running time is displayed.

Error Indications

During abnormal operation, the controller’s displays and
beeper will indicate the error condition that has occurred.

Entrapment

If  an  entrapment  condition  occurs  detected  by  two  repeated
open  or  close  obstruction  triggers,  the  controller  will  lock  the
operator  out.  The  beeper  will  sound  constantly  and  the  gate
will  not  operate.  To  reset  the  controller  press  the

STOP

buttons.

COMM LINK Connection Failure

In dual installations, if there is a connection failure between the
two operators, the

COMM LINK

indicator will blink once a

second. During this condition the gate will not operate, except
if triggered by the

FIRE DEPT

input, which functions normally.

MGT Obstacle Transmitter Trouble

If  any  MGT  transmitters  are  used  with  the  operator,  their
supervision feature will alert the controller if there is any trouble
with  the  transmitter.  MGT  transmitters  send  hourly  status
reports  and  will  send  low  battery  reports  when  the  transmitter
has  a  low  battery.  The  MGT  transmitters  also  have  a  tamper
detection switch that will trigger when their case is opened.
When the controller detects a low transmitter battery, a tamper
signal,  or  missing  transmitter  status  reports,  the  gate  will  still
operate normally, but the beeper will change as follows:



The Pre-start Alarm will beep twice as fast.



The run alarm will beep twice as fast and continue for five

minutes after the gate stops.



The sounder will “chirp” every five seconds when the gate

is idle.

Correct the trouble (close case, replace battery, or replace
transmitter) to clear the obstacle transmitter trouble indications.

Maximum run Time Exceeded

If the Maximum Run Time is exceeded, the controller stops the
operator the same as if a double obstacle has occurred in an
entrapment

condition.

The

entrapment

alarm

sounds

constantly, and is cleared by pressing the

STOP

button. After

the

STOP

RESET

button is pressed, because the Maximum

Run Time has been exceeded, the sounder will beep twice
every five seconds. The next operation of the gate will clear the
indication.

The Stop and/or Reset button must be located in the line-
of-sight of the gate. Activation of the reset control
shall not cause the operator to start.

WARNING

CONTROLLERERROR CAUSES ANDINDICATIONS

ERROR CAUSE

ERROR INDICATION

HOW TO CLEAR

TWO SAFETY REVERSALS
(ON SINGLE GATE OR ON
EITHER DUAL GATE)

En 00, CONTINUOUS
ALARM BEEPER, GATE
DISABED

PRESS STOP BUTTON

MAXIMUM RUN TIMER
EXCEEDED ON OPENING

En 01, AND

MAX RUN

LED,