21
Advance Controller Programming (Cont.)
Radio Enable
The controller contains a built in MegaCode® radio receiver to
allow activation from up to 40 access control transmitters and
two Model MGT (gate edge) transmitters. The factory default
enables the internal radio receiver. Alternately, the internal
receiver can be disabled.
NOTE:
In dual-unit installations, it is recommended to disable
the radio receiver in one of the two operators.
Antenna Installation
The controller is supplied with a local whip antenna installed. If
using a remote antenna, remove the wh ip antenna and
connect coax cable from the antenna to the
ANTENNA
connector.
Radio Transmitter Learn
The controller’s built -in MegaCode® radio receiver can store
the IDs of up to 40 transmitters. Refer to the figure for the
steps required to learn transmi tters.
NOTE:
This function will NOT be displayed if the transmitter
memory is full, or if the radio receiver is disabled.
Radio Transmitter Delete
Transmitters can be deleted from the controller’s memory
either individually, or all at the same time. Refer to the figure
for the steps required to delete transmitters.
NOTE:
This function will NOT be displayed if the transmitter
memory is full, or if the radio receiver is disabled.
MGT Obstacle Transmitter Learn
The controller supports one or two Model MGT Obstacle
Transmitters. The transmitters can be programmed to function
as Open Obstruction, Close Obstruction, Reverse, or Stop.
Refer to the figure for the steps required to learn MGT
NOTE:
This function will NO T be displayed if two MGT transmitters are
already stored in memory, or if the radio receiver is disabled.
MGT Obstacle Transmitter Delete
MGT transmitters can be deleted from the controller’s memory
either individually, or all at the same time. Refer to the figure
for the steps required to delete MGT transmitters.
NOTE:
This function will NOT be displayed if two MGT
transmitters are already stored in memory, or if the radio
receiver is disabled.
Reset Controller to Factory Defaults
The controller can be
reset with this function.
ALL
PROGRAMMED DATA WILL BE LOST,
and the factory
defaults will be loaded. This function will not erase radio
transmitters. Transmitters must be deleted with the two
functions above.
DO NOT RESET CONTROLLER WITHOUT
CONSULTING TECHNICAL SUPPORT AT 877 -331-4747.
FUNCTION
“CL”
ENTER
WHILE “CL” IS DISPLAYED, PRESS ENTER
ALL PROGRAMMED DATA WILL BE
CLEARED AND THE FACTORY DEFAULTS
WILL BE STORED IN MEMORY.
NOTE: THIS FUNCTION WILL NOT ERASE
TRANSMITTERS
RESET TO
FACTORY
FUNCTION
“RA”
OPTION
PRESS UP OR DOWN TO
CYCLE THROUGH
OPTIONS
PRESS ENTER TO
SELECT AN OPTION
INTERNAL RADIO RECEIVER DISABLED
INTERNAL RADIO RECEIVER ENABLED
RADIO
ENABLE
PRESS ENTER, “ML” WILL BLINK FOR 30 SECONDS WHILE THE
CONTROLLER IS READY TO LEARN AN MGT TRANSMITTER
ACTIVATE THE MGT TRANSMITTER, THE DISPLAY WILL
SHOW”_ _” THEN THE TRANSMITTER ID NUMBER – IF THE
TRANSMITTER IS ALREADY ENTERED “DU” WILL BE
DISPLAYED, IF DECODE IS BAD “ERROR” WILL BE DISPLAYED
PRESS ENTER, THE DISPLAY SHOWS DEFAULT MGT
TRANSMITTER FUNCTION (CLOSE OBSTRUCTION)
PRESS UP OR DOWN TO SELECT MGT FUNCTION:
“rE” = REVERSE
“St” = STOP
“OP” = OPEN OBSTRUCTION
“CL” = CLOSE OBSTRUCTION
PRESS ENTER TO STORE OPTION, REPEAT STEPS FOR SECOND
MGT TRANSMITTER IF USED
ENTER
ENTER
ENTER
UP
OR
DOWN
FUNCTION
“ML”
LEARNING MGT
TRANSMITTERS
ENTER
ENTER
ENTER
UP
OR
DOWN
FUNCTION
DELETING
TRANSMITTERS
“TD”
PRESS ENTER
“TD” WILL BLINK FOR 30 SECONDS WHILE THE CONTROLLER IS
READY TO DELETE ONE OR MORE TRANSMITTERS, (TO EXIT
WITHOUT DELETING ANY, PRESS ENTER)
TO DELET ALL TRANSMITTERS, PRESS ENTER FOR 2 SECONDS,
OR TO PICK TRANSMITTERS GO TO NEXT STEP
PRESS UP OR DOWN TO SCROLL THROUGH THE LIST OF
TRANSMITTER ED NUMBERS
THE TRANSMITTER ID NUMBER IS DISPLAYED (TO EXIT
WITHOUT DELETING, PRESS ENT ER) (TO PICK A DIFFERENT
TRANSMITTER ID, PRESS UP OR DOWN
PRESS ENTER FOR 2 SECONDS TO DELETE THE TRANSMITTER
DISPLAYED
PRESS ENTER
“MD” WILL BLINK FOR 30 SECONDS WHILE THE CONTROLLER IS
READY TO DELETE ONE OR MORE MGT TRANSMITTERS. (TO EXIT
WITHOUT DELETING ANY, PRESS ENTER)
TO DELETE ALL MGT TRANSMITTERS, PRESS ENTER FOR 2
SECONDS, OR TO PICK TRANSMITTER GO TO NEXT STEP
PRESS UP OR DOWN TO SCROLL THROUGH THE LIST OF MGT
TRANSMITTER ID NUMBERS
THE MGT TRANSMITTER ID NUMBER IS DISPLAYED (TO EXIT
WITHOUT DELETING, PRESS ENTER) (TO PICK THE OTHER
TRANSMITTER ID, PRESS UP OR DOWN) PRESS ENTER FOR 2
SECONDS TO DELETE THE MGT TRANSMITTER DISPLAYED
ENTER
ENTER
ENTER
UP
OR
DOWN
ERASING MGT
TRANSMITTERS
E
FUNCTION
E
”MD”
Summary of Contents for SL-1000 R
Page 8: ...8 Figure 3...
