Rosslare AYC-E 5 Series Installation And Programming Manual Download Page 24 | Manualshive

Page: 24 / 65

background image

Reader Operation

24

AYC-Ex5/T65 Series Installation and Programming Manual

3.2.4

Selecting Proximity Card Transmission Format

There are three proximity card transmission formats.
More information on each of the proximity card transmission

formats is presented in Section

To select the proximity card transmission format:

1.

Enter Programming mode.

2.

Press

2

to enter Menu 2.

The left LED turns red.

3.

Enter one of the following options:

1

– Wiegand 26-Bit

2

– Clock & Data

3

– Wiegand Card + PIN

You hear three beeps.
The system returns to Standby mode.

3.2.4.1

Proximity Card Transmission Formats

Option 1: Wiegand 26-Bit

In this mode, 3 LSB bytes from the card serial number (UID) are

transmitted in Wiegand 26-Bit format. Two parity bits are added. An

even parity bit is sent first, followed by three bytes of card data, and

by an odd parity bit.
(EP) AAAA AAAA AAAA AAAA AAAA AAAA (OP)
Where:

EP = Even parity for first 12 bits
OP = Odd parity for last 12 bits
A = 3 bytes code generated from card data

Green

Red Green

Red

«
...
22
23
24
25
26
...
»

Summary of Contents for AYC-E 5 Series


































































Reviews:

No comments

Related manuals for AYC-E 5 Series

Brand: Panasonic Pages: 45

Brand: Radarcan Pages: 40

Brand: VADDIO Pages: 2

Brand: Gardena Pages: 16

Brand: MADRIX Pages: 28

Brand: Hach Pages: 36

Brand: Hach Pages: 72

Brand: Harman Pages: 2

Brand: T-Link Pages: 3

ServeRAID-MR10is

Brand: IBM Pages: 94

ServeRAID-4 Ultra160 Series

Brand: IBM Pages: 20

8271 Nways Ethernet LAN Switch

Brand: IBM Pages: 6

Brand: IBM Pages: 86

Brand: IBM Pages: 205

Brand: IBM Pages: 28

Brand: Kärcher Pages: 4

UNDER CONTROL CP-30A PILOT

Brand: G-Force Pages: 2

Brand: IN-COMMAND Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands