manualshive.com logo in svg

Rosslare AYC-E 5 Series, Installation And Programming Manual

Share
Download
Rosslare AYC-E 5 Series Installation And Programming Manual Download Page 26

Reader Operation 

26 

AYC-Ex5/T65 Series Installation and Programming Manual 

Where: 

A = The first key entered 

D = Fourth key entered 

B = Second key entered 

E = Fifth key entered 

C = Third key entered 

 

EP = Even parity for first 12 bits 

OP = Odd parity for last 12 bits 

If the PIN code is less than 5 digits, all the most significant nibbles 

are filled with 0. 
Example: (EP) 0000 0000 0000 0000 AAAA BBBB (OP) 
Where: 

A = The first key entered 

B = Second key entered 

EP = Even parity for first 12 bits 

OP = Odd parity for last 12 bits 

3.2.5

 

Changing the Programming Code 

 

•

 

The Programming code cannot be erased, meaning the code 0000 

is invalid and does not erase the Programming code. 

•

 

The factory default 4-digit Programming code is 1234. 

To change the Programming code: 

1.

 

Enter Programming mode. 

 

2.

 

Press 

3

 to enter Menu 3. 

 

The left LED turns red. 

 

3.

 

Enter the new 4-digit Programming code. 

 

You hear three beeps. 
The system returns to Standby mode. 

 

Green 

Red  Green 

Red 

Summary of Contents for AYC-E 5 Series


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands